On Sun, 11 Sep 2005 14:59:16 -0700 Mark Menke <[EMAIL PROTECTED]> wrote:
> Do you have to passs any special flags to the ivtv module when you > load it? I 've got the same card, but can't get the audio to work. > cat/dev/video0 leaves my with an mpg that has great video and no > audio. FYI regarding thread subject - deal is expired, back to $99. No sir, nothing special, and my cat /dev/video0 test came with crystal clear audio and CPU only spiked briefly (to ~20%) at startup, then back to about 3-5% .. which is normal. I spose I should point out, I captured DVD output using composite cables (which was on Composite 1: ivtvctl -p 3). I don't recall having to manually set a corresponding audio input. I used the firmware from the included CD, and had to tweak ivtvfwextract.pl to do so. I may heed the warning of it's being "buggy!!!" and use one from the ivtv site. Since my shiny new PVR-150 will live under the staircase, I had to build a serial IR receiver in the time since I last replied here (to my amazement, it works!). Point being - I'm probably the _least_ qualified to debug this issue, but I've included my relevant dmesg output. (You may wanna take this to the ivtv list) Having said that - how are you determining the audio is missing? Also, according to dmesg, do you see 'tveeprom: audio processor = CX25841 (type = 23)' or similar? How about 'ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)'? Any error messages? If not, maybe it's as simple as using ivtvctl to get the proper inputs. -Jay ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.8 (svn snapshot revision 2638) loading ivtv: Linux version: 2.6.10-5-k7 preempt K7 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card (iTVC16 based) ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 14 (level, low) -> IRQ 14 lirc_i2c: chip found @ 0x71 (Hauppauge IR (PVR150)) ivtv: i2c attach to card #0 ok [client=Hauppauge IR (PVR150), addr=71] lirc_dev: lirc_register_plugin: sample_rate: 10 tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 0123456 tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = CX25841 (type = 23) tveeprom: decoder processor = CX25841 (type = 1c) ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61] cx25840: loading /lib/modules/HcwMakoA.ROM ivtv: i2c attach to card #0 ok [client=cx25840[50], addr=44] ivtv: i2c attach to card #0 ok [client=wm8775[50], addr=1b] ivtv: loading /lib/modules/ivtv-fw-enc.bin ivtv: Encoder revision: 0x02050032 ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total) ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0 ivtv: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ====================
_______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
