Adam- I am using the remote that came with the PVR-350. when I do a ls -l /dev/lir* I get
[EMAIL PROTECTED] mythtv]# ls -l /dev/lir* srw-rw-rw- 1 root root 0 Jan 10 12:50 /dev/lircd Thanks -Matt Quoting Adam Propeck <[EMAIL PROTECTED]>: > Well, this would be specific to the remote "receiver" you are using. I'm > assuming that you are using the one that comes with the PVR-350. > > What do you see when you run 'ls -l /dev/lir*' as root? You should at a > minimum have an lircd file, but you may have an lirc0 file which might be > the one to point to. Also tell me the output of running 'lircd -n' as root. > You may have to run 'service lircd stop' first. Give me those and I'll check > into some of the specific PVR-350 settings in the mean time. Lirc was a big > problem for me as it seems that the directions are extremely vague for > anyone not using the 250 and 150. Since I have a USB Uirt, I had to figure > some of it out on my own. I still need to figure out how to rebuild Myth > with lirc support built-in. > > On 1/10/06, Matt Rude <[EMAIL PROTECTED]> wrote: >> >> So what execting file should I link to? or am I missing a file? >> -Matt >> >> Quoting Adam Propeck <[EMAIL PROTECTED]>: >> >> > I don't know which /dev file you should be linking the /dev/lirc file to >> > with the PVR-350, but I would recommend that at least while you test, >> just >> > use (as root or via sudo) 'lircd -n' to see the messages immediately and >> > then you don't have to go and look for them. I have a USB-UIRT, and so I >> > ended up having to edit the /etc/sysconfig/lircd file to show -h uirt2 >> > --device=/dev/ttyUSB0 I'd expect that you simply need to edit your >> file >> > appropriately. >> > >> > On 1/9/06, Matt Rude <[EMAIL PROTECTED]> wrote: >> >> >> >> I have Mythtv running on FC4 with a PVR-350. Everything is running but >> the >> >> remote control. I have installed lirc & lirc-kmdl via yum along with >> the >> >> reset >> >> of the Mythtv suite. I edited my modprobe.conf file and ran these >> >> commands. >> >> >> >> $mkdir /home/mythtv/.mythtv >> >> $wget http://wilsonet.com/mythtv/lircrc-haupgrey-g3.txt >> >> $mv lircd-haupgrey-g3.conf.txt ~/.mythtv/lircrc >> >> $/sbin/depmod -a >> >> $/sbin/modprobe lirc_i2c >> >> $/sbin/chkconfig lircd on >> >> $/sbin/service lircd start >> >> >> >> Once this is done I can try to run /usr/bin/irw and the program exits. >> if >> >> I look >> >> at my messages file I get as below. A list for /dev/lircd shows me. >> >> >> >> #ll /dev/lir* >> >> srw-rw-rw- 1 root root 0 Jan 9 20:31 /dev/lircd >> >> >> >> I know I need the lirc0 or lirc. >> >> >> >> >> >> What am I missing to make this work? >> >> any help would be nice. >> >> >> >> >> >> >> >> >> >> ### tail /var/log/messages # Fresh after a reboot >> >> Jan 9 20:28:50 mythtv lircd-0.8.0-CVS[2280]: lircd(any) ready >> >> Jan 9 20:30:03 mythtv lircd-0.8.0-CVS[2280]: accepted new client on >> >> /dev/lircd >> >> Jan 9 20:30:03 mythtv lircd-0.8.0-CVS[2280]: could not get file >> >> information for >> >> /dev/lirc >> >> Jan 9 20:30:03 mythtv lircd-0.8.0-CVS[2280]: default_init(): No such >> file >> >> or >> >> directory >> >> Jan 9 20:30:03 mythtv lircd-0.8.0-CVS[2280]: caught signal >> >> Jan 9 20:31:32 mythtv lircd-0.8.0-CVS[2931]: lircd(any) ready >> >> Jan 9 20:31:49 mythtv lircd-0.8.0-CVS[2931]: accepted new client on >> >> /dev/lircd >> >> Jan 9 20:31:49 mythtv lircd-0.8.0-CVS[2931]: could not get file >> >> information for >> >> /dev/lirc >> >> Jan 9 20:31:49 mythtv lircd-0.8.0-CVS[2931]: default_init(): No such >> file >> >> or >> >> directory >> >> Jan 9 20:31:49 mythtv lircd-0.8.0-CVS[2931]: caught signal >> >> >> >> >> >> ### ll /dev/lirc* >> >> srw-rw-rw- 1 root root 0 Jan 9 20:31 /dev/lircd >> >> >> >> >> >> ### cat /etc/modprobe.conf >> >> # Enable IF >> >> alias char-major-61 lirc_i2c >> >> # From Setup >> >> alias eth0 e100 >> >> alias snd-card-0 snd-intel8x0 >> >> options snd-card-0 index=0 >> >> options snd-intel8x0 index=0 >> >> remove snd-intel8x0 { /usr/sbin/alsactl store 0 >/dev/null 2>&1 || : ; >> }; >> >> /sbin/modprobe -r --ignore-remove snd-intel8x0 >> >> alias usb-controller uhci-hcd >> >> # ivtv modules setup >> >> alias char-major-81 ivtv >> >> alias char-major-81-0 ivtv >> >> alias tveeprom tveeprom-ivtv >> >> alias msp3400 msp3400-ivtv >> >> install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe >> ivtv-fb >> >> install lirc_i2c /sbin/modprobe ivtv; /sbin/modprobe --ignore-install >> >> lirc_i2c >> >> install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 && >> >> /usr/sbin/alsactl restore >/dev/null 2>&1 || : >> >> remove snd-emu10k1 { /usr/sbin/alsactl store >/dev/null 2>&1 || : ; }; >> >> /sbin/modprobe -r --ignore-remove snd-emu10k >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> Thanks >> >> Matt >> >> _______________________________________________ >> >> mythtv-users mailing list >> >> [email protected] >> >> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users >> >> >> > >> >> >> _______________________________________________ >> mythtv-users mailing list >> [email protected] >> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users >> > _______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
