HI John! Thanks! Yes, that is an interesting thread on MSX forum. If anyone can figure out the V9938 registers it is someone there.
I am thinking it might help the conversation there to describe the S-100 Z80 CPU board, S-100 VDP, and S-100 Utility board as one third each of a three board MSX2 suite. The S-100 VDP is intended to be MSX2 compatible since it uses the V9938 and is also able to use the Yamaha YM2149 instead of the AY-3-8910 sound generator. The S-100 Utility also has MSX2 features like the real-time clock chip, etc. There is a cartridge port and matrix ASCII key board port and cassette port. However the cassette port is poorly defined at the moment as I don't quite have all the details on how to implement it. Also includes a parallel port and a serial port. There are some dependencies between the boards like for example the S-100 VDP generates the unique Z80 clock frequency (3.57xxxx MHz) which synchronizes the S-100 Z80 CPU V2 and S-100 VDP V4 boards using a non-defined S-100 bus pin. You can use nearly any frequency Z80 but to get something that works well with the V9938 the CPU needs to be synchronized with it. I am expecting the S-100 Utility board will go through some pretty massive changes for the V2 version once we shake out the bugs, logical fallacies, missing information, and other gaps in the design. I think there is enough there to get a working board but we are still quite a ways from completely functional board. S-100 boards and MSX both have some pretty unique idiosyncrasies and trying to get them to co-exist and cooperate is highly non-intuitive to me. It is pretty clear they both descended from completely different design schools and have little in common. Thanks and have a nice day! Andrew Lynch From: [email protected] [mailto:[email protected]] On Behalf Of John Monahan Sent: Friday, January 24, 2014 11:56 AM To: [email protected] Subject: RE: [N8VEM-S100:2285] Re: Jumpers on Z-80 CPU Card Guys, somewhat related I have opened up a tread with an MSX Forum group that may be able to help us with the related VDP board, and may in fact be able to help here also. To get directly to the relevant tread try:- http://www.msx.org/forum/msx-talk/software/software-s-100-bus-computer-using -msx-video-hardware#comment-229369 Also Neil, in the end it will be very useful if this utility board can sit silently in an S-100 system until called upon, since many users will want to do other things with their system as well. Why can't one boot up with our Z80 board, initialize the 8255, load MSX code to low RAM, jump to it and from there shadow out the Z80 onboard ROM (send 01H to port D3H), giving the full 64K of RAM to the Z80. John From: [email protected] [mailto:[email protected]] On Behalf Of Andrew Lynch Sent: Friday, January 24, 2014 3:35 AM To: [email protected] Subject: Re: [N8VEM-S100:2284] Re: Jumpers on Z-80 CPU Card Thanks Neil! That's great news! I knew this board was going to be a tough one. It looks like I munged the reset sequence in translating from MSX to S-100. Hopefully it is fixable! Thanks and have a nice day! Andrew Lynch From: nbreeden <[email protected]> To: [email protected] Sent: Thursday, January 23, 2014 10:47 PM Subject: Re: [N8VEM-S100:2284] Re: Jumpers on Z-80 CPU Card MSX2 Update. I've been looking in detail at the Goldstar implementation Andrew based the utility board on and have some observations and thoughts on how the Goldstar MSX2 design works. The system on power up or reset needs to be able to access the system BIOS ROM; the ROM is in SLOT Zero starting at address 0x0000. The 8255 PIO is also reset at power up or on system reset resulting in the ports being set to input; this means Port A is not configured to allow access to the BIOS ROM in slot zero; the first few bytes in that ROM configure the 8255 to allow it to control the slots. ; $0000 CHKRAM ; Function : Tests RAM and sets RAM slot for the system ; Registers: All ; Remark : After this, a jump must be made to INIT, for further initialization. chkram: ; Initialize interface ld a,$82 out (PPI_REGS),a ld a,$50 out (GIO_REGS),a ; Initialize memory bank xor a out (MAP_REG4),a inc a out (MAP_REG3),a inc a out (MAP_REG2),a inc a out (MAP_REG1),a We thus have a chicken and egg issue. In the Goldstar design U32A and U32B are configured as a set/reset flip flop. I believe this flip flop is the key to how the system powers up; the sequence would be: Reset 8255 ports are set to input The S/R flip flop holds the G inputs on U27 (74LS153) high; as both G inputs are high the two outputs (1Y and 2Y) are low. These two outputs become the select inputs on U11 (74LS139). As A14/A15 are low (these to the G inputs on the LS139) the outputs of U11 that control slot 0 are low and the system can access the BIOS ROM to run the first few instructions; these run and the 8255 is set to configure the slots. Y5 which is generated by the C port in the 8255 as part of the keyboard scanning; this then clears the S/R flip flop; the G inputs on U27 are set to 0s and the system enters the normal 8255 controlled slot mode. The utility board design is using the 8255 select bit to clear the S/R flip flop; I don't believe this will work as it will reset the S/R flip flop before the 8255 is fully configured. I'll be updating my monitor to configure the 8255 as the MSX2 BIOS does and will see if I need to tweak the utility board to match the Goldstar design. -Neil -Neil -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out. -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out. -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out. -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
