Hi Josh, I'll take three. I can wait for Mid-April too.
Thanks! Todd * Crusty OMO <[email protected]> [140304 09:17]: > Hi, > > I'm ready to go for a run of these Mini-buffered Prototyping boards. > > Shipping varies. But you have 2 options. I can ship up to 5 boards in a box > from Canada for $16 (flat rate small package) > or you can wait until Mid-April, I can cross the boarder and ship in strong > cardboard envelopes at Andrew's rates. > > I want to get some pre-orders, before making the run. > > Regards, > Josh Bensadon > > > Date: Sun, 2 Mar 2014 09:56:43 -0500 > Subject: Re: [N8VEM-S100:2601] Re: Board Run: Unbuffered Prototyping > From: [email protected] > To: [email protected] > > I very much like what you'd done with the sea-flow. > > Personally, I'd never put a DBxx directly on an S100 board. Instead use an > IDC-type cable with a 2xN connector and ribbon . The DBxx belongs on the > bulkhead. So I'm not enthusiastic about that change. > > > As for the LED, perhaps a placement consistent with what's used on the 80286 > master/Slave CPU Board would avoid the (potential) card ejector handle. Or > maybe just scrap it and let folks wire what they want, if they want anything > at all? After all, they'll probably be bringing PWR/GND "around" for ICs > anyway. So let them wire-where-they-will, rather than committing to that > corner? (OTOH, they can always just cut the trace ...) > > > > > > On Sat, Mar 1, 2014 at 11:12 PM, Crusty OMO <[email protected]> wrote: > > > > > Guys, Please find attached latest art work for this board. > I've done away with the 14 pin dips and let the "Sea of PTH" flow into that > area. > Power runs through it. > I mixed in the terminations for S-100 bus to the lowest 2 rows of of the sea. > > > Look at top right, I added a DB connector, less the DB mounting holes. > I think it would be very handy to have this option, one can always put an IC > over top the skewed pins if they don't want DB9. I'll keep the DB9 there > unless it gets voted off the island (or sea). > > > It looks like it's ready to go... 2 questions still loom. > 1. Position of LED, > 2. Size of holes (I reduced to .038 from .042... I'm now thinking that was a > mistake) > > Cheers, > Josh > > > > > > > > > > > > > -- > > You received this message because you are subscribed to the Google Groups > "N8VEM-S100" group. > > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > > For more options, visit https://groups.google.com/groups/opt_out. > > > > > > > > -- > > You received this message because you are subscribed to the Google Groups > "N8VEM-S100" group. > > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > > For more options, visit https://groups.google.com/groups/opt_out. > > > -- > You received this message because you are subscribed to the Google Groups > "N8VEM-S100" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/groups/opt_out. -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
