Sorry about the mis-send there; hit the wrong key! Corrected marking is "FSO11PH50-DR-H-DH". They look factory-original and IMO are quite nice. No regrets here :->.
On Sat, Jun 14, 2014 at 1:29 PM, Paul Birkel <[email protected]> wrote: > I purchased 20 when Ants was early-on in his backplane design. They fit a > 17-slot MITS original backplane that I subsequently picked up on eBay as > well as the thicker 8-slot design from N8VEM -- with an appropriate amount > of solder-tail above the thick N8VEM PCB for a quality solder-joint. > > They're lookmarked FSO11PH50-DR-H-DR 7936 > > > On Sat, Jun 14, 2014 at 1:18 PM, Edward Snider <[email protected]> > wrote: > >> Have you bought these before Paul? >> >> I'm shopping for 26 connectors for Ants backplane and one of the 8-slot >> boards. >> Have to be sure they'll fit. >> >> Ed >> >> >> On Saturday, June 14, 2014 2:08:47 AM UTC-5, pbirkel wrote: >> >>> You might consider Anchor Electronics. Catalog: >>> http://anchor-electronics.com/price-list.pdf >>> >>> On Page 17 you'll find that for the 100-pin edgeboard connectors: >>> >>> Solder-tail $3.95 >>> Wire-wrap $6.95 >>> Best prices that I've found *anywhere* (excepting occasionally on eBay >>> for WW). Note that shipping is FedEx (no exceptions), so the actual >>> cost-delivered will be higher per-item. Orders only phone-or-fax. >>> They are a great source for numerous hard-to-find components. >>> >>> But ordering _just_ 3 solder-tail connectors is probably not going to be >>> nearly as cost-effective as it looks at first-glance once you factor in the >>> shipping. >>> >>> On Fri, Jun 13, 2014 at 6:41 PM, J. Alexander Jacocks <[email protected] >>> > wrote: >>> >>>> Brian, >>>> >>>> Yep, I think that you are right. >>>> >>>> Todd, >>>> >>>> Do you have any connectors for sale? I need 3, it looks like. >>>> >>>> All, >>>> >>>> I have a mix of flanged and non-flanged connectors. Do the flanges >>>> make a lot of difference? I'd normally want them all to match, but the >>>> cost of the connectors is high. >>>> >>>> Thanks! >>>> - Alex >>>> >>>> >>>> On Fri, Jun 13, 2014 at 5:36 PM, Brian Marstella <[email protected]> >>>> wrote: >>>> >>>>> Hi, Alex, >>>>> >>>>> I think the ones you're looking at from Digikey are the wrong pitch; >>>>> the pins are spaced at .1 and I think the S-100 connectors are .125. >>>>> >>>>> Regards, Brian. >>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "N8VEM-S100" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to [email protected]. >>>>> >>>>> For more options, visit https://groups.google.com/d/optout. >>>>> >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "N8VEM-S100" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> -- >> You received this message because you are subscribed to the Google Groups >> "N8VEM-S100" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> > > -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
