Hi All! We are running Nagios 3.0 on RHEL 5.1 and are trying to get YAPS 0.96 with an AVM Fritz PCI ISDN card to work as our notification system. capiinfo seems to be showing the correct information:
Number of Controllers : 1 Controller 1: Manufacturer: AVM GmbH CAPI Version: 2.0 Manufacturer Version: 3.11-07 (49.23) Serial Number: 1000001 BChannels: 2 .... This indicates to me that the driver is correctly installed and we can see the card. (Is this correct?) I run yaps like this /usr/bin/yaps 0170XXXXXX "TEST" And get this output: Found service D1-0170 for 0170XXXXXX Sending following message: 0170XXXXXX (D1-0170, 0170XXXXXX): TEST Trying to open /dev/ttyI0 for modem standard [Hangup] [Send] <cr> [Cmd Mdzz 200] [Send] ATZ<cr> [Expect] <cr>ATZ<cr><cr><lf>OK got OK [Send] AT&E55430<cr> [Expect] <cr><lf>AT&E55430<cr><cr><lf>OK got OK Using modem standard at 38400 bps, 8n1 over /dev/ttyI0 Trying do dial 01712521002 [Send] ATDT001712521002<cr> [Expect] <cr><lf>ATDT001712521002<cr><cr><lf>NO DIALTONE got NO DIALTONE Unable to dial D1-0170 The NO DIALTONE comes immediately (i.e. no time out). I have googled for the last several hours and have not found anything definitive. The closest to anything definitive is that Fritz cards work primarily with SUSE. Unfortunately, I have found nothing specifically for RHES 5.1 (kernel 2.6.18-53.el5) which describes exactly modules to load and in which order. However, since capiinfo reports the info from the card, I assume that it is a configuration issue with yaps or the connection, in general. (see below for loaded modules) The yaps works from another machine using the same connection. It is in a different room, so we have to go throug a couple of patch panels. I have switch that cables and am now using new ones I took right out of the bag. Perhaps the patch panels have a problem. Up to the final [Expect] the output appear identical. /dev/ttyI0 looks like this: crw-r--r-- 1 root root 43, 0 Jun 2 18:04 /dev/ttyI0 I was thinking about forcing yaps not to wait for a dialtone, so in /etc/yaps.rc I changed this dial ATDT0%L\r <60CONNECT|OK|BUSY|NO\sDIALTONE|NO\sCARRIER to this: dial ATDT0X3%L\r <60CONNECT|OK|BUSY|NO\sCARRIER I no longer get "NO DIALTONE" immediately, but I get a timeout after 30 seconds. I would be grateful for any assistance. Regards, Jim Mohr ============= lsmod: Module Size Used by fcpci 597376 0 hisax_isac 11989 0 hisax 356093 1 hisax_isac crc_ccitt 6337 1 hisax isdn 122305 1 hisax slhc 10561 1 isdn capi 20993 0 kernelcapi 48705 2 fcpci,capi capifs 9801 2 capi autofs4 24389 2 hidp 23105 2 rfcomm 42457 0 l2cap 29633 10 hidp,rfcomm bluetooth 53925 5 hidp,rfcomm,l2cap sunrpc 144253 1 ip6t_REJECT 9409 1 xt_tcpudp 7105 6 ip6table_filter 6849 1 ip6_tables 18181 1 ip6table_filter x_tables 17349 3 ip6t_REJECT,xt_tcpudp,ip6_tables ipv6 251393 45 ip6t_REJECT dm_multipath 21577 0 video 19269 0 sbs 18533 0 backlight 10049 0 i2c_ec 9025 1 sbs button 10705 0 battery 13637 0 asus_acpi 19289 0 ac 9157 0 lp 15849 0 floppy 57125 0 joydev 13313 0 sg 36061 0 ide_cd 40033 0 parport_pc 29157 1 parport 37513 2 lp,parport_pc cdrom 36705 1 ide_cd e1000 119505 0 i2c_i801 11469 0 tg3 104133 0 i2c_core 23745 2 i2c_ec,i2c_i801 serio_raw 10693 0 pcspkr 7105 0 dm_snapshot 20709 0 dm_zero 6209 0 dm_mirror 28741 0 dm_mod 58201 15 dm_multipath,dm_snapshot,dm_zero,dm_mirror ata_piix 18501 0 libata 115833 1 ata_piix megaraid_sas 31345 3 sd_mod 24897 5 scsi_mod 132685 4 sg,libata,megaraid_sas,sd_mod ext3 123337 5 jbd 56553 1 ext3 ehci_hcd 32973 0 ohci_hcd 23261 0 uhci_hcd 25421 0 ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ _______________________________________________ Nagios-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/nagios-users ::: Please include Nagios version, plugin version (-v) and OS when reporting any issue. ::: Messages without supporting info will risk being sent to /dev/null
