Ok, I am going to order the Solid State relay from Fred today, I have a vfd drive running a 3 phase motor. Here is a link to a schematic for the control. I am assuming I run a 5v pin and ground pin from the break out board to the SSR. Then where do I hook the other terminals on the SSR to the vfd? Here is the link http://www.kbelectronics.com/manuals/kbvf.pdf
--- In [EMAIL PROTECTED], "JamesCullins" <[EMAIL PROTECTED]> wrote: > It will disable the out signals in the absents of the charge pump signal > form Mach2. > This signal is a tone of about 13 kHz. When Mach2 is reset the signal > appears and the out puts are enabled. If Mach2 isn't running then you get > nothing out. > Jim > ----- Original Message ----- > From: "turbulatordude" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Thursday, December 16, 2004 7:39 PM > Subject: [CAD_CAM_EDM_DRO] Re: Turning Spindle Off and On > > > > > > > > > > > ///What about opto-isolation? Wouldnt there be a risk of damaging > > the PC electronics wiring up auxillary equiptment directly to the > > port? > > > > > > All the SSR's I have looked at have opto isolation as well as do > > Gecko's. > > > > > > The Cambell board does offer additional features that may or may not > > be required. > > > > There are a lot of people who wire directly into the port, from > > electronics hobbyists, to telescope people to machine tool people. > > > > Also, for my machines on machine tools, I keep them dedicated and > > simple software loaded. > > > > If you plan to surf the internet and use your machine as a general > > purpose machine, while you use your Bridgeport, you accept the risk > > of a virus doing bad things as well as having your registry cluttered. > > > > > > > Other breakout boards have the ability to control Solid state > > relays however like the PMDX has no "watchdog" feature that monitors > > erroneous pulses from the PC (it didn't two years ago anyway and they > > didn't sound too concerned about changing it). > > > > > > I'm not sure what signal the Cambell board does that differentiates a > > signal to the port from an erroneous signal. > > > > Dave > > > > > > > > > > > > > > Addresses: > > FAQ: http://www.ktmarketing.com/faq.html > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/ > > Post Messages: [EMAIL PROTECTED] > > > > Subscribe: [EMAIL PROTECTED] > > Unsubscribe: [EMAIL PROTECTED] > > List owner: [EMAIL PROTECTED], [EMAIL PROTECTED], > [EMAIL PROTECTED] > > Moderator: [EMAIL PROTECTED] [EMAIL PROTECTED] [EMAIL PROTECTED] > [Moderators] > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO > > > > OFF Topic POSTS: General Machining > > If you wish to post on unlimited OT subjects goto: > aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if > you have trouble. > > http://www.metalworking.com/news_servers.html > > > > http://groups.yahoo.com/group/jobshophomeshop I consider this to be a > sister site to the CCED group, as many of the same members are there, for OT > subjects, that are not allowed on the CCED list. > > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........ > > bill > > List Mom > > List Owner > > > > > > Yahoo! Groups Links > > > > > > > > > > > > > > Addresses: FAQ: http://www.ktmarketing.com/faq.html FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/ Post Messages: [EMAIL PROTECTED] Subscribe: [EMAIL PROTECTED] Unsubscribe: [EMAIL PROTECTED] List owner: [EMAIL PROTECTED], [EMAIL PROTECTED], [EMAIL PROTECTED] Moderator: [EMAIL PROTECTED] [EMAIL PROTECTED] [EMAIL PROTECTED] [Moderators] URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO OFF Topic POSTS: General Machining If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble. http://www.metalworking.com/news_servers.html http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list. NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........ bill List Mom List Owner Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/
