No idea if tg3 is to blame. Its a JS20, root on ext3 on raid0 on qla23xx
fibrechannel
16 hours uptime, it did some package building, no special workload, some
ftp download, some nfs upload.
Slab corruption: start=c00000000a7c4e60, len=2048
Redzone: 0x5a2cf071/0x5a2cf071.
Last user: [<c00000000022330c>](.release_mem+0x120/0x2a0)
120: ff ff ff ff 00 00 00 00 6b 6b 6b 6b 6b 6b 6b 6b
Prev obj: start=c00000000a7c4648, len=2048
Redzone: 0x5a2cf071/0x5a2cf071.
Last user: [<c0000000000eb454>](.free_fdtable_rcu+0xa4/0x128)
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
Next obj: start=c00000000a7c5678, len=2048
Redzone: 0x170fc2a5/0x170fc2a5.
Last user: [<d0000000002e6330>](.tg3_alloc_rx_skb+0xd8/0x1b8 [tg3])
000: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a
010: 5a 5a ff ff ff ff ff ff 00 0d 60 f6 15 eb 81 00
Page orders: linear mapping = 24, others = 12
Found initrd at 0xc000000002300000:0xc00000000261d1a8
Starting Linux PPC64 #1 SMP Tue Feb 28 09:16:17 UTC 2006
-----------------------------------------------------
ppc64_pft_size = 0x19
ppc64_interrupt_controller = 0x2
platform = 0x101
physicalMemorySize = 0x5c000000
ppc64_caches.dcache_line_size = 0x80
ppc64_caches.icache_line_size = 0x80
htab_address = 0x0000000000000000
htab_hash_mask = 0x3ffff
-----------------------------------------------------
[boot]0100 MM Init
[boot]0100 MM Init Done
Linux version 2.6.16-rc5-git2-20060228091617-ppc64 ([EMAIL PROTECTED]) (gcc
version 4.1.0 20060223 (prerelease) (SUSE Linux)) #1 SMP Tue Feb 28 09:16:17
UTC 2006
[boot]0012 Setup Arch
Top of RAM: 0x5c000000, Total RAM: 0x5c000000
Memory hole size: 0MB
PPC64 nvram contains 16384 bytes
Using default idle loop
On node 0 totalpages: 376832
DMA zone: 376832 pages, LIFO batch:31
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: root=/dev/md0 sysrq=1 quiet
[boot]0020 XICS Init
xics: no ISA interrupt controller
[boot]0021 XICS Done
PID hash table entries: 4096 (order: 12, 131072 bytes)
time_init: decrementer frequency = 199.836166 MHz
time_init: processor frequency = 1600.000000 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
freeing bootmem node 0
Memory: 1464112k/1507328k available (4336k kernel code, 43216k reserved, 1956k
data, 852k bss, 252k init)
Calibrating delay loop... 398.95 BogoMIPS (lpj=1994752)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
checking if image is initramfs... it is
Freeing initrd memory: 3188k freed
Processor 1 found.
Brought up 2 CPUs
migration_cost=819
NET: Registered protocol family 16
Installing base platform functions...
All base functions installed
PCI: Probing PCI hardware
IOMMU table initialized, virtual merging enabled
IDE Fixup IRQ: Can't find IO-APIC !
mapping IO 100f4000000 -> d000080000000000, size: 400000
PCI: Probing PCI hardware done
Registering pmac pic with sysfs...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
TC classifier action (bugs to netdev@vger.kernel.org cc [EMAIL PROTECTED])
IBM eBus Device Driver
probe_bus_pseries: processing c00000005bffcc48
RTAS daemon started
RTAS: event: 20, Type: Unknown, Severity: 1
RTAS: event: 21, Type: Unknown, Severity: 1
probe_bus_pseries: processing c00000005bffcda8
probe_bus_pseries: processing c00000005bffcef0
audit: initializing netlink socket (disabled)
audit(1141427449.409:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
vio_register_driver: driver hvc_console registering
HVSI: registered 0 devices
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
pmac_zilog: 0.6 (Benjamin Herrenschmidt <[EMAIL PROTECTED]>)
RAMDISK driver initialized: 16 RAM disks of 123456K size 1024 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD8111: IDE controller at PCI slot 0000:00:04.1
AMD8111: chipset revision 3
AMD8111: 0000:00:04.1 (rev 03) UDMA133 controller
AMD8111: 100% native mode on irq 32
ide0: BM-DMA at 0x7c00-0x7c07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x7c08-0x7c0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK6026GAXB, ATA DISK drive
ide0 at 0x7400-0x7407,0x6c02 on irq 32
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB), CHS=65535/16/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0000:21:00.0: OHCI Host Controller
ohci_hcd 0000:21:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:21:00.0: irq 35, io mem 0x100e0001000
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.16-rc5-git2-20060228091617-ppc64 ohci_hcd
usb usb1: SerialNumber: 0000:21:00.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:21:00.1: OHCI Host Controller
ohci_hcd 0000:21:00.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:21:00.1: irq 35, io mem 0x100e0000000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.16-rc5-git2-20060228091617-ppc64 ohci_hcd
usb usb2: SerialNumber: 0000:21:00.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
oprofile: using ppc64/970 performance monitoring.
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Freeing unused kernel memory: 252k freed
SCSI subsystem initialized
QLogic Fibre Channel HBA Driver
PCI: Enabling device: (0000:01:01.0), cmd 147
qla2xxx 0000:01:01.0: Found an ISP2312, irq 40, iobase 0xd000080080002000
qla2xxx 0000:01:01.0: Configuring PCI space...
qla2xxx 0000:01:01.0: Configure NVRAM parameters...
qla2xxx 0000:01:01.0: Verifying loaded RISC code...
qla2xxx 0000:01:01.0: Extended memory detected (512 KB)...
qla2xxx 0000:01:01.0: Resizing request queue depth (2048 -> 4096)...
qla2xxx 0000:01:01.0: Waiting for LIP to complete...
qla2xxx 0000:01:01.0: LOOP UP detected (2 Gbps).
qla2xxx 0000:01:01.0: Topology - (F_Port), Host Loop address 0xffff
scsi0 : qla2xxx
qla2xxx 0000:01:01.0:
QLogic Fibre Channel HBA Driver: 8.01.04-k
QLogic IBM FCEC -
ISP2312: PCI-X (133 MHz) @ 0000:01:01.0 hdma-, host#=0, fw=3.03.18 IPX
PCI: Enabling device: (0000:01:01.1), cmd 143
qla2xxx 0000:01:01.1: Found an ISP2312, irq 41, iobase 0xd000080080003000
Vendor: IBM Model: 2105F20 Rev: .307
Type: Direct-Access ANSI SCSI revision: 03
qla2xxx 0000:01:01.1: Configuring PCI space...
qla2xxx 0000:01:01.1: Configure NVRAM parameters...
SCSI device sda: 19531264 512-byte hdwr sectors (10000 MB)
sda: Write Protect is off
sda: Mode Sense: 93 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 19531264 512-byte hdwr sectors (10000 MB)
sda: Write Protect is off
sda: Mode Sense: 93 00 00 08
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
Vendor: IBM Model: 2105F20 Rev: .307
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sdb: 19531264 512-byte hdwr sectors (10000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 8b 00 00 08
SCSI device sdb: drive cache: write back
SCSI device sdb: 19531264 512-byte hdwr sectors (10000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 8b 00 00 08
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3
sd 0:0:0:1: Attached scsi disk sdb
qla2xxx 0000:01:01.1: Verifying loaded RISC code...
Vendor: IBM Model: 2105F20 Rev: .307
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sdc: 19531264 512-byte hdwr sectors (10000 MB)
sdc: Write Protect is off
sdc: Mode Sense: 8b 00 00 08
SCSI device sdc: drive cache: write back
SCSI device sdc: 19531264 512-byte hdwr sectors (10000 MB)
sdc: Write Protect is off
sdc: Mode Sense: 8b 00 00 08
SCSI device sdc: drive cache: write back
sdc:<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:1: Attached scsi generic sg1 type 0
sdc1 sdc2 sdc3
sd 0:0:0:2: Attached scsi disk sdc
sd 0:0:0:2: Attached scsi generic sg2 type 0
Vendor: IBM Model: 2105F20 Rev: .307
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sdd: 19531264 512-byte hdwr sectors (10000 MB)
sdd: Write Protect is off
sdd: Mode Sense: 8b 00 00 08
SCSI device sdd: drive cache: write back
SCSI device sdd: 19531264 512-byte hdwr sectors (10000 MB)
sdd: Write Protect is off
sdd: Mode Sense: 8b 00 00 08
SCSI device sdd: drive cache: write back
sdd: sdd1 sdd2 sdd3
sd 0:0:0:3: Attached scsi disk sdd
sd 0:0:0:3: Attached scsi generic sg3 type 0
qla2xxx 0000:01:01.1: Extended memory detected (512 KB)...
qla2xxx 0000:01:01.1: Resizing request queue depth (2048 -> 4096)...
qla2xxx 0000:01:01.1: Waiting for LIP to complete...
qla2xxx 0000:01:01.1: Cable is unplugged...
scsi1 : qla2xxx
qla2xxx 0000:01:01.1:
QLogic Fibre Channel HBA Driver: 8.01.04-k
QLogic IBM FCEC -
ISP2312: PCI-X (133 MHz) @ 0000:01:01.1 hdma-, host#=1, fw=3.03.18 IPX
md: raid0 personality registered for level 0
md: md0 stopped.
md: bind<sdc3>
md: bind<sdb3>
md0: setting max_sectors to 64, segment boundary to 16383
raid0: looking at sdb3
raid0: comparing sdb3(8683008) with sdb3(8683008)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sdc3
raid0: comparing sdc3(8683008) with sdb3(8683008)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 17366016 blocks.
raid0 : conf->hash_spacing is 17366016 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1048816k swap on /dev/hda2. Priority:-1 extents:1 across:1048816k
Adding 1052248k swap on
/dev/disk/by-path/pci-0000:01:01.0-fc-0x5005076300c990a9:0x0001000000000000-part2.
Priority:-2 extents:1 across:1052248k
Adding 1052248k swap on
/dev/disk/by-path/pci-0000:01:01.0-fc-0x5005076300c990a9:0x0002000000000000-part2.
Priority:-3 extents:1 across:1052248k
EXT3 FS on md0, internal journal
tg3.c:v3.49 (Feb 2, 2006)
PCI: Enabling device: (0000:11:01.0), cmd 142
eth0: Tigon3 [partno(none) rev 2003 PHY(serdes)] (PCIX:133MHz:64-bit)
10/100/1000BaseT Ethernet 00:0d:60:1e:cc:f4
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[0] TSOcap[0]
eth0: dma_rwctrl[769f4000]
PCI: Enabling device: (0000:11:01.1), cmd 142
eth1: Tigon3 [partno(none) rev 2003 PHY(serdes)] (PCIX:133MHz:64-bit)
10/100/1000BaseT Ethernet 00:0d:60:1e:cc:f5
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth1: dma_rwctrl[769f4000]
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [EMAIL PROTECTED]
dm-netlink version 0.0.2 loaded
loop: loaded (max 8 devices)
AppArmor: AppArmor (version 2.0-19.43r6152) initialized
audit(1141427483.929:2): AppArmor (version 2.0-19.43r6152) initialized
JBD: barrier-based sync failed on md0 - disabling barriers
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is off for TX and off for RX.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
JBD: barrier-based sync failed on md0 - disabling barriers
JBD: barrier-based sync failed on md0 - disabling barriers
eth1: no IPv6 routers present
Slab corruption: start=c00000000a7c4e60, len=2048
Redzone: 0x5a2cf071/0x5a2cf071.
Last user: [<c00000000022330c>](.release_mem+0x120/0x2a0)
120: ff ff ff ff 00 00 00 00 6b 6b 6b 6b 6b 6b 6b 6b
Prev obj: start=c00000000a7c4648, len=2048
Redzone: 0x5a2cf071/0x5a2cf071.
Last user: [<c0000000000eb454>](.free_fdtable_rcu+0xa4/0x128)
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
Next obj: start=c00000000a7c5678, len=2048
Redzone: 0x170fc2a5/0x170fc2a5.
Last user: [<d0000000002e6330>](.tg3_alloc_rx_skb+0xd8/0x1b8 [tg3])
000: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a
010: 5a 5a ff ff ff ff ff ff 00 0d 60 f6 15 eb 81 00
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
