On Thu, Mar 03, 2016 at 03:38:35PM +0000, Ramesh Shanmugasundaram wrote:
> This patch adds support for the CAN FD controller found in Renesas R-Car
> SoCs. The controller operates in CAN FD mode by default.
>
> CAN FD mode supports both Classical CAN & CAN FD frame formats. The
> controller supports ISO 11898-1:2015 CAN FD format only.
>
> This controller supports two channels and the driver can enable either
> or both of the channels.
>
> Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one
> per channel) for transmission. Rx filter rules are configured to the
> minimum (one per channel) and it accepts Standard, Extended, Data &
> Remote Frame combinations.
>
> Note: There are few documentation errors in R-Car Gen3 Hardware User
> Manual v0.5E with respect to CAN FD controller. They are listed below:
>
> 1. CAN FD interrupt numbers 29 & 30 are listed as per channel
> interrupts. However, they are common to both channels (i.e.) they are
> global and channel interrupts respectively.
>
> 2. CANFD clock is derived from PLL1. This is not documented.
>
> 3. CANFD clock is further divided by (1/2) within the CAN FD controller.
> This is not documented.
>
> 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It
> is mentioned 4 Tq in the manual.
>
> 5. The maximum number of message RAM area the controller can use is 3584
> bytes. It is specified 10752 bytes in the manual.
>
> Signed-off-by: Ramesh Shanmugasundaram
> <ramesh.shanmugasunda...@bp.renesas.com>
> ---
> Changes since v1:
> * Removed testmodes & debugfs code (suggested by Oliver H)
> * Fixed tx path race issue by introducing lock (suggested by Marc K)
> * Removed __maybe_unused attribute of rcar_canfd_of_table
>
> Thanks,
> Ramesh
> ---
> .../devicetree/bindings/net/can/rcar_canfd.txt | 86 ++
> drivers/net/can/Kconfig | 10 +
> drivers/net/can/Makefile | 1 +
> drivers/net/can/rcar_canfd.c | 1624
> ++++++++++++++++++++
> 4 files changed, 1721 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/can/rcar_canfd.txt
> create mode 100644 drivers/net/can/rcar_canfd.c
>
> diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt
> b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt
> new file mode 100644
> index 0000000..4299bd8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt
> @@ -0,0 +1,86 @@
> +Renesas R-Car CAN FD controller Device Tree Bindings
> +----------------------------------------------------
> +
> +Required properties:
> +- compatible: Must contain one or more of the following:
> + - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller.
> + - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller.
> +
> + When compatible with the generic version, nodes must list the
> + SoC-specific version corresponding to the platform first, followed by the
> + family-specific and/or generic versions.
> +
> +- reg: physical base address and size of the R-Car CAN FD register map.
> +- interrupts: interrupt specifier for the Global & Channel interrupts
> +- clocks: phandles and clock specifiers for 3 clock inputs.
> +- clock-names: 3 clock input name strings: "fck", "canfd", "can_clk".
> +- pinctrl-0: pin control group to be used for this controller.
> +- pinctrl-names: must be "default".
> +
> +Required properties for "renesas,r8a7795-canfd" compatible:
> +In R8A7795 SoC, canfd clock is a div6 clock and can be used by both CAN
> +and CAN FD controller at the same time. It needs to be scaled to maximum
> +frequency if any of these controllers use it. This is done using the
> +below properties.
> +
> +- assigned-clocks: phandle of canfd clock.
> +- assigned-clock-rates: maximum frequency of this clock.
> +
> +Each channel is represented as a child node. They can be enabled/disabled
> +using "status" property.
How many channels? Required or optional?
> +
> +Example
> +-------
> +
> +SoC common .dtsi file:
> +
> + canfd: canfd@e66c0000 {
can@e66c0000
> + compatible = "renesas,r8a7795-canfd",
> + "renesas,rcar-gen3-canfd";
> + reg = <0 0xe66c0000 0 0x8000>;
> + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cpg CPG_MOD 914>,
> + <&cpg CPG_CORE R8A7795_CLK_CANFD>,
> + <&can_clk>;
> + clock-names = "fck", "canfd", "can_clk";
> + assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>;
> + assigned-clock-rates = <40000000>;
> + power-domains = <&cpg>;
> + status = "disabled";
> +
> + channel0 {
> + status = "disabled";
> + };
> +
> + channel1 {
> + status = "disabled";
> + };
> + };
> +
> +Board specific .dts file:
> +
> +E.g. below enables Channel 1 alone in the board.
> +
> +&canfd {
> + pinctrl-0 = <&canfd1_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + channel1 {
> + status = "okay";
> + };
> +};
> +
> +E.g. below enables Channel 0 alone in the board using External clock
> +as fCAN clock.
> +
> +&canfd {
> + pinctrl-0 = <&canfd0_pins &can_clk_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + channel0 {
> + status = "okay";
> + };
> +};
