On Fri, Apr 08, 2016 at 11:38:58AM +0200, Jesper Dangaard Brouer wrote:
>
> On Thu, 7 Apr 2016 21:48:47 -0700 Brenden Blanco <bbla...@plumgrid.com>
> wrote:
>
> > Add two new set/get netdev ops for drivers implementing the
> > BPF_PROG_TYPE_PHYS_DEV filter.
> >
> > Signed-off-by: Brenden Blanco <bbla...@plumgrid.com>
> [...]
> >
> > diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
> > index cb4e508..3acf732 100644
> > --- a/include/linux/netdevice.h
> > +++ b/include/linux/netdevice.h
> [...]
> > @@ -1102,6 +1103,14 @@ struct tc_to_netdev {
> > * appropriate rx headroom value allows avoiding skb head copy on
> > * forward. Setting a negative value resets the rx headroom to the
> > * default value.
> > + * int (*ndo_bpf_set)(struct net_device *dev, struct bpf_prog *prog);
> > + * This function is used to set or clear a bpf program used in the
> > + * earliest stages of packet rx. The prog will have been loaded as
> > + * BPF_PROG_TYPE_PHYS_DEV. The callee is responsible for calling
> > + * bpf_prog_put on any old progs that are stored, but not on the passed
> > + * in prog.
> > + * bool (*ndo_bpf_get)(struct net_device *dev);
> > + * This function is used to check if a bpf program is set on the device.
> > *
>
> This interface for the entire device, right. I can imagine that users
> want to attach a eBPF program per RX queue. Can we adapt the interface
> to support this? (could default to adding it all queues)
>
Currently yes, for the entire device. I don't see rx queue exposed in
common setlink APIs. Wouldn't this be available only through ethtool,
generally? That would be a significant change to the api, but not a lot
of code. I would defer to others on which is cleaner. An alternative
could be to always run the program, but expose the queue number in
struct bpf_phys_dev_md. That is not as flexible since the program is
still shared, but maybe still useful.
>
> I'm also wondering if we should add a "flags" parameter. Or maybe we
> can extend 'struct bpf_prog' with I have in mind.
>
> When the eBPF program is attached to a RX queue, I want to know if the
> program want to modify packet-data, up-front.
>
> The problem is that most drivers use dma_sync, which means that data is
> considered 'read-only' (the "considered" part depend on DMA engine, and
> we might find a DMA loop-hole for some configs).
> If the program want to write, the driver have the option of
> reconfiguring the driver routine to use dma_unmap, before handing over
> the page. Or driver can also choose to realloc the specific RX ring
> queue pages as single pages (using dma_map/unmap consistently).
> This also allow us to give a return code indicating given driver does
> not support writable packet-pages (rejecting program).
When write-mode is enabled for this prog type, we'll add the flag. I
don't want to add unused flags prematurely. When we add such support, it
should be available in the bpf_prog struct, similar to the cb_access or
dst_needed bool fields.
>
> --
> Best regards,
> Jesper Dangaard Brouer
> MSc.CS, Principal Kernel Engineer at Red Hat
> Author of http://www.iptv-analyzer.org
> LinkedIn: http://www.linkedin.com/in/brouer
