Why is this necessary? There is already an ethtool function to set the rx ring size (pcnet32_set_ringparam). Since module parameters are being phased out in favor of the ethtool functions, why not use the existing ethtool infrastructure for this?
Thanks, Jon On Mon, May 15, 2006 at 11:32:14AM +0800, Wen Hsin Chang wrote: > This patch is created from pcnet32.c v1.32. it will allow users to > specify RX ring size upon module > insertion via module parameter 'rx_log_size'. This is needed in some > cases where too small the rx ring > size will cause RX errors upon remote installation via pcnet32 NIC card. > > Signed-off-by: Wen Hsin Chang <[EMAIL PROTECTED]> > ---------------------------------------------------------------------------------------------------- > > --- a/drivers/net/pcnet32.c 2006-03-30 09:49:10.000000000 +0800 > +++ b/drivers/net/pcnet32.c 2006-05-15 11:14:45.000000000 +0800 > @@ -93,6 +93,9 @@ static struct net_device *pcnet32_dev; > static int max_interrupt_work = 2; > static int rx_copybreak = 200; > > +/* Module parameter to specify RX ring size at module insertion */ > +static int rx_log_size = 0; > + > #define PCNET32_PORT_AUI 0x00 > #define PCNET32_PORT_10BT 0x01 > #define PCNET32_PORT_GPSI 0x02 > @@ -1264,7 +1267,10 @@ pcnet32_probe1(unsigned long ioaddr, int > lp->name = chipname; > lp->shared_irq = shared; > lp->tx_ring_size = TX_RING_SIZE; /* default tx ring size */ > - lp->rx_ring_size = RX_RING_SIZE; /* default rx ring size */ > + if (!rx_log_size) > + lp->rx_ring_size = RX_RING_SIZE; /* default rx ring size */ > + else > + lp->rx_ring_size = (1 << (rx_log_size)); > lp->tx_mod_mask = lp->tx_ring_size - 1; > lp->rx_mod_mask = lp->rx_ring_size - 1; > lp->tx_len_bits = (PCNET32_LOG_TX_BUFFERS << 12); > @@ -2707,6 +2713,11 @@ module_param(tx_start_pt, int, 0); > MODULE_PARM_DESC(tx_start_pt, DRV_NAME " transmit start point (0-3)"); > module_param(pcnet32vlb, int, 0); > MODULE_PARM_DESC(pcnet32vlb, DRV_NAME " Vesa local bus (VLB) support > (0/1)"); > + > +/* Module parameter to specify RX ring size at module insertion */ > +module_param(rx_log_size, int, 0); > +MODULE_PARM_DESC(rx_log_size, DRV_NAME " RX Ring Buffer Size (log_2 > #BUF) "); > + > module_param_array(options, int, NULL, 0); > MODULE_PARM_DESC(options, DRV_NAME " initial option setting(s) (0-15)"); > module_param_array(full_duplex, int, NULL, 0); > @@ -2731,6 +2742,12 @@ static int __init pcnet32_init_module(vo > > if ((tx_start_pt >= 0) && (tx_start_pt <= 3)) > tx_start = tx_start_pt; > + > + /* validating rx_log_size */ > + if ((rx_log_size <= 0) || > + (rx_log_size > PCNET32_LOG_MAX_RX_BUFFERS)) > + rx_log_size = 0; > + > > /* find the PCI devices */ > if (!pci_module_init(&pcnet32_driver)) > > - > To unsubscribe from this list: send the line "unsubscribe netdev" in > the body of a message to [EMAIL PROTECTED] > More majordomo info at http://vger.kernel.org/majordomo-info.html - To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
