On Tue, Sep 6, 2016 at 11:46 AM, Michal Soltys <sol...@ziu.info> wrote: > Hi, > > I've been testing different configurations and I didn't manage to get XPS to > "behave" correctly - so I'm probably misunderstanding or forgetting > something. The nic in question (under tg3 driver - BCM5720 and BCM5719 > models) was configured to 3 tx and 4 rx queues. 3 irqs were shared (tx and > rx), 1 was unused (this got me scratching my head a bit) and the remaining > one was for the last rx (though due to another bug recently fixed the 4th rx > queue was inconfigurable on receive side). The names were: eth1b-0, > eth1b-txrx-1, eth1b-txrx-2, eth1b-txrx-3, eth1b-rx-4. > > The XPS was configured as: > > echo f >/sys/class/net/eth1b/queues/tx-0/xps_cpus > echo f0 >/sys/class/net/eth1b/queues/tx-1/xps_cpus > echo ff00 >/sys/class/net/eth1b/queues/tx-2/xps_cpus > > So as far as I understand - cpus 0-3 should be allowed to use tx-0 queue > only, 4-7 tx-1 and 8-15 tx-2. > > Just in case rx side could get in the way as far as flows go, relevant irqs > were pinned to specific cpus - txrx-1 to 2, txrx-2 to 4, txrx-3 to 10 - > falling into groups defined by the above masks. > > I tested both with mx and multiq scheduler, essentially either this: > > qdisc mq 2: root > qdisc pfifo_fast 0: parent 2:1 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 > 1 > qdisc pfifo_fast 0: parent 2:2 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 > 1 > qdisc pfifo_fast 0: parent 2:3 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 > 1 > > or this (for the record, skbaction queue_mapping was behaving correctly with > the one below): > > qdisc multiq 3: root refcnt 6 bands 3/5 > qdisc pfifo_fast 31: parent 3:1 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 > 1 1 > qdisc pfifo_fast 32: parent 3:2 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 > 1 1 > qdisc pfifo_fast 33: parent 3:3 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 > 1 1 > > Now, do I understand correctly, that under the above setup - commands such as > > taskset 400 nc -p $prt host_ip 12345 </dev/zero > or > yancat -i /dev/zero -o t:host_ip:12345 -u 10 -U 10 > > ITOW - pinning simple nc command on cpu #10 (or using a tool that supports > affinity by itself) and sending data to some other host on the net - should > *always* use tx-2 queue ? > I also tested variation such as: taskset 400 nc -l -p host_ip 12345 > </dev/zero (just in case taskset was "too late" with the affinity). > > In my case, what queue it used was basically random (on top of that it > sometimes changed the used queue mid-transfer) what could be easily confirmed > through both /proc/interrupts and tc -s qdisc show. And I'm a bit at loss > now, as I though xps configuration should be absolute. > > Well, I'd be greatful for some pointers / hints.
So it sounds like you have everything configured correctly. The one question I would have is if we are certain the CPU pinning is working for the application. You might try using something like perf to verify what is running on CPU 10, and what is running on the CPUs that the queues are associated with. Also after you have configured things you may want to double check and verify the xps_cpus value is still set. I know under some circumstances the value can be reset by a device driver if the number of queues changes, or if the interface toggles between being administratively up/down. Thanks. - Alex
