Às 11:24 AM de 1/4/2017, Niklas Cassel escreveu: > > > On 01/04/2017 12:08 PM, Joao Pinto wrote: >> Hi Niklas, >> >> Às 10:59 AM de 1/4/2017, Niklas Cassel escreveu: >>> Hello Joao >>> >>> I just tested this series using the dwc_eth_qos DT bindings. >>> Good work! >>> >>> Unfortunately I get the following error: >>> >>> <3>[ 12.032463] dwc-eth-dwmac f8010000.ethernet eth0: stmmac_open: ERROR: >>> allocating the WoL IRQ -1098801248 (-22) >>> >>> >>> This appears to be because of a corner case in stmmac_platform.c >>> where wol_irq can differ from the normal irq. >>> >>> Adding the following one liner fixes the problem: >>> >>> >>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>> @@ -125,6 +125,7 @@ static int dwc_eth_dwmac_probe(struct platform_device >>> *pdev) >>> } >>> return stmmac_res.irq; >>> } >>> + stmmac_res.wol_irq = stmmac_res.irq; >>> >>> res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >>> stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res); >>> >> Ok, I'll add this fix to the patch and give a check to the clks. >> I already sent a v1 patch set to net-dev, and I am now going to generate v2 >> so >> it would be great to have your tested.by tag to push it faster :) Thanks! > > Send your V2, and I will test it, and reply with a Tested-by tag. > I can't reply with a Tested-by tag on V1, since it gives an > error during open. > > If I reply with a Tested-by tag, on your V2, patchwork > https://urldefense.proofpoint.com/v2/url?u=https-3A__patchwork.ozlabs.org_project_netdev_list_&d=DgID-g&c=DPL6_X_6JkXFx7AXWqB0tg&r=s2fO0hii0OGNOv9qQy_HRXy-xAJUD1NNoEcc3io_kx0&m=Ne_JFvbqIwFj_Tokwm6Yv1pv3wETnoD3iG7TjxJqLaQ&s=7hU48UexRw1mb7Y3V4ly3tX0yErTXUW_k4gSZVGe4yE&e= > > will append it to the patch automatically. > Since Dave fetches patches from patchwork, > it will be there when it's time to be applied.
Ok, great! Just sent you v2. Thanks. > >> >>> >>> >>> I have one comment about clocks interleaved as well >>> >>> >>> >>> On 01/04/2017 10:44 AM, Joao Pinto wrote: >>>> This patch adds a new glue driver called dwmac-dwc-qos-eth which >>>> was based in the dwc_eth_qos as is. To assure retro-compatibility a slight >>>> tweak was also added to stmmac_platform. >>>> >>>> Signed-off-by: Joao Pinto <[email protected]> >>>> Reviewed-by: Lars Persson <[email protected]> >>>> --- >>>> .../bindings/net/snps,dwc-qos-ethernet.txt | 3 + >>>> drivers/net/ethernet/stmicro/stmmac/Kconfig | 9 + >>>> drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + >>>> .../ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c | 199 >>>> +++++++++++++++++++++ >>>> .../net/ethernet/stmicro/stmmac/stmmac_platform.c | 15 +- >>>> 5 files changed, 224 insertions(+), 3 deletions(-) >>>> create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>>> >>>> diff --git >>>> a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>>> b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>>> index d93f71c..21d27aa 100644 >>>> --- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>>> +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>>> @@ -1,5 +1,8 @@ >>>> * Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) >>>> >>>> +This binding is deprecated, but it continues to be supported, but new >>>> +features should be preferably added to the stmmac binding document. >>>> + >>>> This binding supports the Synopsys Designware Ethernet QoS (Quality Of >>>> Service) >>>> IP block. The IP supports multiple options for bus type, clocking and >>>> reset >>>> structure, and feature list. Consequently, a number of properties and list >>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig >>>> b/drivers/net/ethernet/stmicro/stmmac/Kconfig >>>> index ab66248..99594e3 100644 >>>> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig >>>> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig >>>> @@ -29,6 +29,15 @@ config STMMAC_PLATFORM >>>> >>>> if STMMAC_PLATFORM >>>> >>>> +config DWMAC_DWC_QOS_ETH >>>> + tristate "Support for snps,dwc-qos-ethernet.txt DT binding." >>>> + select PHYLIB >>>> + select CRC32 >>>> + select MII >>>> + depends on OF && HAS_DMA >>>> + help >>>> + Support for chips using the snps,dwc-qos-ethernet.txt DT binding. >>>> + >>>> config DWMAC_GENERIC >>>> tristate "Generic driver for DWMAC" >>>> default STMMAC_PLATFORM >>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile >>>> b/drivers/net/ethernet/stmicro/stmmac/Makefile >>>> index 8f83a86..700c603 100644 >>>> --- a/drivers/net/ethernet/stmicro/stmmac/Makefile >>>> +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile >>>> @@ -16,6 +16,7 @@ obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o >>>> obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o >>>> obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o >>>> obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o >>>> +obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o >>>> obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o >>>> stmmac-platform-objs:= stmmac_platform.o >>>> dwmac-altr-socfpga-objs := altr_tse_pcs.o dwmac-socfpga.o >>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>>> b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>>> new file mode 100644 >>>> index 0000000..8a6ac06 >>>> --- /dev/null >>>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>>> @@ -0,0 +1,199 @@ >>>> +/* >>>> + * Synopsys DWC Ethernet Quality-of-Service v4.10a linux driver >>>> + * >>>> + * Copyright (C) 2016 Joao Pinto <[email protected]> >>>> + * >>>> + * This program is free software; you can redistribute it and/or modify >>>> + * it under the terms of the GNU General Public License version 2 as >>>> + * published by the Free Software Foundation. >>>> + * >>>> + * You should have received a copy of the GNU General Public License >>>> + * along with this program. If not, see >>>> <https://urldefense.proofpoint.com/v2/url?u=http-3A__www.gnu.org_licenses_&d=DgIC-g&c=DPL6_X_6JkXFx7AXWqB0tg&r=s2fO0hii0OGNOv9qQy_HRXy-xAJUD1NNoEcc3io_kx0&m=DrobFP08nu4hh6e05EgeOl1xD34OacyiZ-be_GG829Q&s=WLSkpBK06KCu-_kvN305yE6YncNYcDG_Bk0pgqSBG1o&e=>. >>>> + */ >>>> + >>>> +#include <linux/clk.h> >>>> +#include <linux/clk-provider.h> >>>> +#include <linux/device.h> >>>> +#include <linux/ethtool.h> >>>> +#include <linux/io.h> >>>> +#include <linux/ioport.h> >>>> +#include <linux/module.h> >>>> +#include <linux/of_net.h> >>>> +#include <linux/mfd/syscon.h> >>>> +#include <linux/platform_device.h> >>>> +#include <linux/stmmac.h> >>>> + >>>> +#include "stmmac_platform.h" >>>> + >>>> +static int dwc_eth_dwmac_config_dt(struct platform_device *pdev, >>>> + struct plat_stmmacenet_data *plat_dat) >>>> +{ >>>> + struct device_node *np = pdev->dev.of_node; >>>> + u32 burst_map = 0; >>>> + u32 bit_index = 0; >>>> + u32 a_index = 0; >>>> + >>>> + if (!plat_dat->axi) { >>>> + plat_dat->axi = kzalloc(sizeof(struct stmmac_axi), GFP_KERNEL); >>>> + >>>> + if (!plat_dat->axi) >>>> + return -ENOMEM; >>>> + } >>>> + >>>> + plat_dat->axi->axi_lpi_en = of_property_read_bool(np, "snps,en-lpi"); >>>> + if (of_property_read_u32(np, "snps,write-requests", >>>> + &plat_dat->axi->axi_wr_osr_lmt)) { >>>> + /** >>>> + * Since the register has a reset value of 1, if property >>>> + * is missing, default to 1. >>>> + */ >>>> + plat_dat->axi->axi_wr_osr_lmt = 1; >>>> + } else { >>>> + /** >>>> + * If property exists, to keep the behavior from dwc_eth_qos, >>>> + * subtract one after parsing. >>>> + */ >>>> + plat_dat->axi->axi_wr_osr_lmt--; >>>> + } >>>> + >>>> + if (of_property_read_u32(np, "read,read-requests", >>>> + &plat_dat->axi->axi_rd_osr_lmt)) { >>>> + /** >>>> + * Since the register has a reset value of 1, if property >>>> + * is missing, default to 1. >>>> + */ >>>> + plat_dat->axi->axi_rd_osr_lmt = 1; >>>> + } else { >>>> + /** >>>> + * If property exists, to keep the behavior from dwc_eth_qos, >>>> + * subtract one after parsing. >>>> + */ >>>> + plat_dat->axi->axi_rd_osr_lmt--; >>>> + } >>>> + of_property_read_u32(np, "snps,burst-map", &burst_map); >>>> + >>>> + /* converts burst-map bitmask to burst array */ >>>> + for (bit_index = 0; bit_index < 7; bit_index++) { >>>> + if (burst_map & (1 << bit_index)) { >>>> + switch (bit_index) { >>>> + case 0: >>>> + plat_dat->axi->axi_blen[a_index] = 4; break; >>>> + case 1: >>>> + plat_dat->axi->axi_blen[a_index] = 8; break; >>>> + case 2: >>>> + plat_dat->axi->axi_blen[a_index] = 16; break; >>>> + case 3: >>>> + plat_dat->axi->axi_blen[a_index] = 32; break; >>>> + case 4: >>>> + plat_dat->axi->axi_blen[a_index] = 64; break; >>>> + case 5: >>>> + plat_dat->axi->axi_blen[a_index] = 128; break; >>>> + case 6: >>>> + plat_dat->axi->axi_blen[a_index] = 256; break; >>>> + default: >>>> + break; >>>> + } >>>> + a_index++; >>>> + } >>>> + } >>>> + >>>> + /* dwc-qos needs GMAC4, AAL, TSO and PMT */ >>>> + plat_dat->has_gmac4 = 1; >>>> + plat_dat->dma_cfg->aal = 1; >>>> + plat_dat->tso_en = 1; >>>> + plat_dat->pmt = 1; >>>> + >>>> + return 0; >>>> +} >>>> + >>>> +static int dwc_eth_dwmac_probe(struct platform_device *pdev) >>>> +{ >>>> + struct plat_stmmacenet_data *plat_dat; >>>> + struct stmmac_resources stmmac_res; >>>> + struct resource *res; >>>> + int ret; >>>> + >>>> + /** >>>> + * Since stmmac_platform supports name IRQ only, basic platform >>>> + * resource initialization is done in the glue logic. >>>> + */ >>>> + stmmac_res.irq = platform_get_irq(pdev, 0); >>>> + if (stmmac_res.irq < 0) { >>>> + if (stmmac_res.irq != -EPROBE_DEFER) { >>>> + dev_err(&pdev->dev, >>>> + "IRQ configuration information not found\n"); >>>> + } >>>> + return stmmac_res.irq; >>>> + } >>>> + >>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >>>> + stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res); >>>> + if (IS_ERR(stmmac_res.addr)) >>>> + return PTR_ERR(stmmac_res.addr); >>>> + >>>> + plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); >>>> + if (IS_ERR(plat_dat)) >>>> + return PTR_ERR(plat_dat); >>>> + >>>> + plat_dat->stmmac_clk = devm_clk_get(&pdev->dev, "phy_ref_clk"); >>>> + if (IS_ERR(plat_dat->stmmac_clk)) { >>>> + dev_err(&pdev->dev, "apb_pclk clock not found.\n"); >>> Error message does not match the devm_clk_get. >>> >>> Looking at synopsys/dwc_eth_qos.c >>> phy_ref_clk is just a dummy, used for verbosity. >>> apb_pclk is the clock which is actually used for setting csr etc. >>> >>> So it should be >>> >>> plat_dat->stmmac_clk = devm_clk_get(&pdev->dev, "apb_pclk"); >>> >>> >>> So that way the warning is already correct :) >>> >>> >>> >>>> + ret = PTR_ERR(plat_dat->stmmac_clk); >>>> + plat_dat->stmmac_clk = NULL; >>>> + goto err_remove_config_dt; >>>> + } >>>> + clk_prepare_enable(plat_dat->stmmac_clk); >>>> + >>>> + plat_dat->pclk = devm_clk_get(&pdev->dev, "apb_pclk"); >>>> + if (IS_ERR(plat_dat->pclk)) { >>>> + dev_err(&pdev->dev, "phy_ref_clk clock not found.\n"); >>> Error message does not match the devm_clk_get, >>> however, since this should be >>> >>> plat_dat->pclk = devm_clk_get(&pdev->dev, "phy_ref_clk"); >>> >>> the warning is correct :) >>> >>>> + ret = PTR_ERR(plat_dat->pclk); >>>> + plat_dat->pclk = NULL; >>>> + goto err_out_clk_dis_phy; >>>> + } >>>> + clk_prepare_enable(plat_dat->pclk); >>>> + >>>> + ret = dwc_eth_dwmac_config_dt(pdev, plat_dat); >>>> + if (ret) >>>> + goto err_out_clk_dis_aper; >>>> + >>>> + ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); >>>> + if (ret) >>>> + goto err_out_clk_dis_aper; >>>> + >>>> + return 0; >>>> + >>>> +err_out_clk_dis_aper: >>>> + clk_disable_unprepare(plat_dat->pclk); >>>> +err_out_clk_dis_phy: >>>> + clk_disable_unprepare(plat_dat->stmmac_clk); >>>> +err_remove_config_dt: >>>> + stmmac_remove_config_dt(pdev, plat_dat); >>>> + >>>> + return ret; >>>> +} >>>> + >>>> +static int dwc_eth_dwmac_remove(struct platform_device *pdev) >>>> +{ >>>> + return stmmac_pltfr_remove(pdev); >>>> +} >>>> + >>>> +static const struct of_device_id dwc_eth_dwmac_match[] = { >>>> + { .compatible = "snps,dwc-qos-ethernet-4.10", }, >>>> + { } >>>> +}; >>>> +MODULE_DEVICE_TABLE(of, dwc_eth_dwmac_match); >>>> + >>>> +static struct platform_driver dwc_eth_dwmac_driver = { >>>> + .probe = dwc_eth_dwmac_probe, >>>> + .remove = dwc_eth_dwmac_remove, >>>> + .driver = { >>>> + .name = "dwc-eth-dwmac", >>>> + .of_match_table = dwc_eth_dwmac_match, >>>> + }, >>>> +}; >>>> +module_platform_driver(dwc_eth_dwmac_driver); >>>> + >>>> +MODULE_AUTHOR("Joao Pinto <[email protected]>"); >>>> +MODULE_DESCRIPTION("Synopsys DWC Ethernet Quality-of-Service v4.10a >>>> driver"); >>>> +MODULE_LICENSE("GPL v2"); >>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>>> b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>>> index 4e44f9c..00c0f8d 100644 >>>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>>> @@ -181,10 +181,19 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data >>>> *plat, >>>> mdio = false; >>>> } >>>> >>>> - /* If snps,dwmac-mdio is passed from DT, always register the MDIO */ >>>> - for_each_child_of_node(np, plat->mdio_node) { >>>> - if (of_device_is_compatible(plat->mdio_node, "snps,dwmac-mdio")) >>>> + /* exception for dwmac-dwc-qos-eth glue logic */ >>>> + if (of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) { >>>> + plat->mdio_node = of_get_child_by_name(np, "mdio"); >>>> + } else { >>>> + /** >>>> + * If snps,dwmac-mdio is passed from DT, always register >>>> + * the MDIO >>>> + */ >>>> + for_each_child_of_node(np, plat->mdio_node) { >>>> + if (of_device_is_compatible(plat->mdio_node, >>>> + "snps,dwmac-mdio")) >>>> break; >>>> + } >>>> } >>>> >>>> if (plat->mdio_node) { >
