Le 09/03/17 à 05:31, Baruch Siach a écrit :
> Add device-tree binding documentation SFP transceivers. Support for SFP
> transceivers has been recently introduced (drivers/net/phy/sfp.c).
>
> Signed-off-by: Baruch Siach <[email protected]>
> ---
> v3:
> Mention gpios phandle and specifier
> Mention the polarity of each gpio
> Fix example property names
>
> v2:
> Rename -gpio properties to -gpios
> Rename the rate-select-gpio property to rate-select0-gpios
> Add the rate-select1-gpios property
> Add examples
> ---
> Documentation/devicetree/bindings/net/sff,sfp.txt | 78
> +++++++++++++++++++++++
> 1 file changed, 78 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/sff,sfp.txt
>
> diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt
> b/Documentation/devicetree/bindings/net/sff,sfp.txt
> new file mode 100644
> index 000000000000..b98ee5945265
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/sff,sfp.txt
> @@ -0,0 +1,78 @@
> +Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
> +Transceiver
> +
> +Required properties:
> +
> +- compatible : must be "sff,sfp"
> +
> +Optional Properties:
> +
> +- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial
> + interface
> +
> +- moddef0-gpios : GPIO phandle and a single specifier of the MOD-DEF0 (AKA
> + Mod_ABS) module presence input gpio signal, active (module absent) high
Sorry for nitpicking on this, why are not we naming this mod-def0-gpios
which would be consistent with how other GPIOs are named?
> +
> +- los-gpios : GPIO phandle and a single specifier of the Receiver Loss of
> + Signal Indication input gpio signal, active (signal lost) high
> +
> +- tx-fault-gpios : GPIO phandle and a single specifier of the Module
> + Transmitter Fault input gpio signal, active (fault condition) high
> +
> +- tx-disable-gpios : GPIO phandle and a single specifier of the Transmitter
> + Disable output gpio signal, active (Tx disable) high
> +
> +- rate-select0-gpios : GPIO phandle and a single specifier of the Rx
> Signaling
> + Rate Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx
> + rate
> +
> +- rate-select1-gpios : GPIO phandle and a single specifier of the Tx
> Signaling
> + Rate Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate,
> + high: high Tx rate
> +
> +Example #1: Direct serdes to SFP connection
> +
> +sfp_eth3: sfp-eth3 {
> + compatible = "sff,sfp";
> + i2c-bus = <&sfp_1g_i2c>;
> + los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
> + moddef0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
> + tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
> + tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&cps_emac3 {
> + phy-mode = "sgmii";
> + phy-names = "comphy";
> + phys = <&cps_comphy 5 COMPHY_SGMII2>;
> + sfp = <&sfp_eth3>;
> +};
> +
> +Example #2: Serdes to PHY to SFP connection
> +
> +sfp_eth0: sfp-eth0 {
> + compatible = "sff,sfp+";
> + i2c-bus = <&sfpp0_i2c>;
> + los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
> + moddef0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&cps_sfpp0_pins>;
> + tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
> + tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
> +};
> +
> +p0_phy: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + pinctrl-names = "default";
> + pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
> + reg = <0>;
> + interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
> + sfp = <&sfp_eth0>;
> +};
> +
> +&cpm_eth0 {
> + phy = <&p0_phy>;
> + phy-mode = "10gbase-kr";
> +};
>
--
Florian
