On Tuesday 03 October 2006 05:44, Larry Finger wrote: > Michael Buesch wrote: > > Hi John, > > > > Please pull from my tree > > git pull http://bu3sch.de/git/wireless-dev.git for-linville > > > > This will pull various bugfixes and feature improvements. > > Most noteably it will pull a bugfix for a crash introduced > > by an earlier patch to d80211 which changed RX status information > > handling. > > > > The new features include support for the new v4 firmware. > > I also did my homework to get better support for OpenWRT > > devices in ssb. > > > > > > The list of pulled changesets is: > > > > Michael Buesch: > > ssb: Abstract bus accesses. > > bcm43xx-d80211: convert to ssb abstract bus access API > > bcm43xx-d80211: Don't crash if we use v4 firmware. > > bcm43xx-d80211: Always make fwpostfix option available. > > bcm43xx-d80211: Firmware revision/patchlevel detection. > > bcm43xx-d80211: Add support for v4 firmware. > > bcm43xx-d80211: add SHM constants > > bcm43xx-d80211: Don't use low level netif and ieee80211_netif_oper > > functions. > > bcm43xx-d80211: DMA-mask fixes. > > bcm43xx-d80211: Remove some BCM947XX ifdefs, > > Merge branch 'master' of git://kernel.org/.../linville/wireless-dev > > bcm43xx-d80211: Assign all fields in the RX status report. > > bcm43xx-d80211: Set channel cookie to prevent ghost packets. > > bcm43xx-d80211: Prevent crash by setting active wlcore to NULL on > > wlcore-select failure. > > > > > > The diffstat is: > > > > drivers/misc/ssb.c | 431 ++++++----- > > drivers/net/wireless/d80211/bcm43xx/bcm43xx.h | 143 +++ > > .../net/wireless/d80211/bcm43xx/bcm43xx_debugfs.c | 295 +++----- > > .../net/wireless/d80211/bcm43xx/bcm43xx_debugfs.h | 35 - > > drivers/net/wireless/d80211/bcm43xx/bcm43xx_dma.c | 149 ++-- > > drivers/net/wireless/d80211/bcm43xx/bcm43xx_dma.h | 18 > > drivers/net/wireless/d80211/bcm43xx/bcm43xx_leds.c | 16 > > drivers/net/wireless/d80211/bcm43xx/bcm43xx_main.c | 820 > > +++++++++----------- > > drivers/net/wireless/d80211/bcm43xx/bcm43xx_phy.c | 76 +- > > drivers/net/wireless/d80211/bcm43xx/bcm43xx_pio.c | 104 +-- > > drivers/net/wireless/d80211/bcm43xx/bcm43xx_pio.h | 12 > > .../net/wireless/d80211/bcm43xx/bcm43xx_power.c | 125 +--- > > .../net/wireless/d80211/bcm43xx/bcm43xx_radio.c | 143 ++-- > > .../net/wireless/d80211/bcm43xx/bcm43xx_radio.h | 1 > > drivers/net/wireless/d80211/bcm43xx/bcm43xx_xmit.c | 309 +++++++- > > drivers/net/wireless/d80211/bcm43xx/bcm43xx_xmit.h | 247 +++++- > > include/linux/ssb.h | 71 +- > > 17 files changed, 1681 insertions(+), 1314 deletions(-) > > > Michael, > > There is something wrong with wireless-dev after I pulled your changes. The > logs are: > > kernel: ssb: Core 0 found: cc 0800, rev 02, vendor 4243 > kernel: ssb: Core 1 found: cc 0812, rev 04, vendor 4243 > kernel: ssb: Core 2 found: cc 080D, rev 01, vendor 4243 > kernel: ssb: Core 3 found: cc 0807, rev 01, vendor 4243 > kernel: ssb: Core 4 found: cc 0804, rev 07, vendor 4243 > kernel: ssb: Core 5 found: cc 0812, rev 04, vendor 4243 > kernel: bcm43xx_d80211: Ignoring additional 802.11 core. > kernel: bcm43xx_d80211: Broadcom 4306 WLAN found > kernel: ssb: Switching to core 4 > kernel: bcm43xx_d80211: PHY connected > kernel: ssb: Switching to core 1 > kernel: bcm43xx_d80211: Detected PHY: Version: 1, Type 2, Revision 1 > kernel: bcm43xx_d80211: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 > Rev: 2) > kernel: bcm43xx_d80211: Radio turned off > kernel: bcm43xx_d80211: Radio turned off > kernel: wmaster0: Selected rate control algorithm 'simple' > kernel: bcm43xx_d80211: Virtual interface added (type: 0x00000002, ID: 4, > MAC: 00 > :06:25:40:6f:03) > kernel: bcm43xx_d80211: PHY connected > kernel: bcm43xx_d80211: PHY disconnected > kernel: bcm43xx_d80211: PHY connected > kernel: bcm43xx_d80211: firmware revision FE84, patchlevel 90B4, date > 2000-14-248 > 29:46:18
Uhm, which firmware are you running? > kernel: ssb: Switching to core 0 > kernel: ssb: Switching to core 1 > kernel: bcm43xx_d80211: Radio turned on > kernel: bcm43xx_d80211: Chip initialized > kernel: bcm43xx_d80211: 30-bit DMA initialized > kernel: bcm43xx_d80211: TODO: Incomplete code in keymac_write() at > drivers/net/wireless/d80211/bcm43xx/bcm43xx_main.c:871 > ..... > kernel: bcm43xx_d80211: Keys cleared > kernel: bcm43xx_d80211: Selected 802.11 core (phytype 2) > kernel: wmaster0: Does not support passive scan, disabled > kernel: wlan1: starting scan > kernel: HW CONFIG: channel=1 freq=2412 phymode=3 > kernel: HW CONFIG: channel=2 freq=2417 phymode=3 > kernel: bcm43xx_d80211: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR > kernel: bcm43xx_d80211: ASSERTION FAILED (0) at: > drivers/net/wireless/d80211/bcm43xx/bcm43xx_dma.c:1020:parse_cookie() > kernel: bcm43xx_d80211: ASSERTION FAILED (ring && *slot >= 0 && *slot < > ring->nr_slots) at: > drivers/net/wireless/d80211/bcm43xx/bcm43xx_dma.c:1023:parse_cookie() > kernel: bcm43xx_d80211: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR > kernel: bcm43xx_d80211: ASSERTION FAILED (0) at: > drivers/net/wireless/d80211/bcm43xx/bcm43xx_dma.c:1020:parse_cookie() > kernel: bcm43xx_d80211: ASSERTION FAILED (ring && *slot >= 0 && *slot < > ring->nr_ > slots) at: > drivers/net/wireless/d80211/bcm43xx/bcm43xx_dma.c:1023:parse_cookie() > > If you need any other info, please contact me. > > Larry > -- Greetings Michael. - To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
