Take out the code that protects driver from accessing the
PCI config space.
We are old enough to run with scissors now.
Signed-off-by: Stephen Hemminger <[EMAIL PROTECTED]>
---
drivers/net/sky2.c | 9 ---------
1 file changed, 9 deletions(-)
--- a/drivers/net/sky2.c 2007-08-29 11:40:09.000000000 -0700
+++ b/drivers/net/sky2.c 2007-08-29 11:40:53.000000000 -0700
@@ -603,7 +603,6 @@ static void sky2_phy_power(struct sky2_h
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
onoff = !onoff;
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
if (onoff)
/* Turn off phy power saving */
@@ -613,7 +612,6 @@ static void sky2_phy_power(struct sky2_h
sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
sky2_pci_read32(hw, PCI_DEV_REG1);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
udelay(100);
}
@@ -681,11 +679,9 @@ static void sky2_wol_init(struct sky2_po
sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl);
/* Turn on legacy PCI-Express PME mode */
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
reg1 |= PCI_Y2_PME_LEGACY;
sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
/* block receiver */
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
@@ -2386,10 +2382,8 @@ static void sky2_hw_intr(struct sky2_hw
dev_err(&hw->pdev->dev, "PCI hardware error (0x%x)\n",
pci_err);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
sky2_pci_write16(hw, PCI_STATUS,
pci_err | PCI_STATUS_ERROR_BITS);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
if (status & Y2_IS_PCI_EXP) {
@@ -2403,11 +2397,8 @@ static void sky2_hw_intr(struct sky2_hw
pex_err);
/* clear the interrupt */
- sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
sky2_pci_write32(hw, PEX_UNC_ERR_STAT,
0xffffffffUL);
- sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
-
if (pex_err & PEX_FATAL_ERRORS) {
u32 hwmsk = sky2_read32(hw, B0_HWE_IMSK);
hwmsk &= ~Y2_IS_PCI_EXP;
@@ -2670,7 +2661,6 @@ static void sky2_reset(struct sky2_hw *h
/* clear PCI errors, if any */
status = sky2_pci_read16(hw, PCI_STATUS);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
sky2_pci_write16(hw, PCI_STATUS, status | PCI_STATUS_ERROR_BITS);
@@ -2693,8 +2683,6 @@ static void sky2_reset(struct sky2_hw *h
| GMC_BYP_RETR_ON);
}
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
-
/* Clear I2C IRQ noise */
sky2_write32(hw, B2_I2C_IRQ, 1);
--
Stephen Hemminger <[EMAIL PROTECTED]>
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
