On Mon, 2015-03-30 at 21:54 -0600, Iván Sánchez Vallejo wrote:
> Hello Everyone!!!
>
> Perform some tests and more but I still fix my problem
You'll also probably want "method=ignore" for [ipv6]. But what log
messages does NetworkManager report when it doesn't work?
Dan
> My kernel
> 3.19.2-201.fc21.x86_64
>
> iw phy phy0 info
> Wiphy phy0
> max # scan SSIDs: 20
> max scan IEs length: 195 bytes
> Coverage class: 0 (up to 0m)
> Device supports RSN-IBSS.
> Supported Ciphers:
> * WEP40 (00-0f-ac:1)
> * WEP104 (00-0f-ac:5)
> * TKIP (00-0f-ac:2)
> * CCMP (00-0f-ac:4)
> Available Antennas: TX 0 RX 0
> Supported interface modes:
> * IBSS
> * managed
> * AP
> * AP/VLAN
> * monitor
> Band 1:
> Capabilities: 0x1072
> HT20/HT40
> Static SM Power Save
> RX Greenfield
> RX HT20 SGI
> RX HT40 SGI
> No RX STBC
> Max AMSDU length: 3839 bytes
> DSSS/CCK HT40
> Maximum RX AMPDU length 8191 bytes (exponent: 0x000)
> Minimum RX AMPDU time spacing: 4 usec (0x05)
> HT RX MCS rate indexes supported: 0-15
> TX unequal modulation not supported
> HT TX Max spatial streams: 1
> HT TX MCS rate indexes supported may differ
> Bitrates (non-HT):
> * 1.0 Mbps
> * 2.0 Mbps (short preamble supported)
> * 5.5 Mbps (short preamble supported)
> * 11.0 Mbps (short preamble supported)
> * 6.0 Mbps
> * 9.0 Mbps
> * 12.0 Mbps
> * 18.0 Mbps
> * 24.0 Mbps
> * 36.0 Mbps
> * 48.0 Mbps
> * 54.0 Mbps
> Frequencies:
> * 2412 MHz [1] (15.0 dBm)
> * 2417 MHz [2] (15.0 dBm)
> * 2422 MHz [3] (15.0 dBm)
> * 2427 MHz [4] (15.0 dBm)
> * 2432 MHz [5] (15.0 dBm)
> * 2437 MHz [6] (15.0 dBm)
> * 2442 MHz [7] (15.0 dBm)
> * 2447 MHz [8] (15.0 dBm)
> * 2452 MHz [9] (15.0 dBm)
> * 2457 MHz [10] (15.0 dBm)
> * 2462 MHz [11] (15.0 dBm)
> * 2467 MHz [12] (15.0 dBm) (no IR)
> * 2472 MHz [13] (15.0 dBm) (no IR)
> Supported commands:
> * new_interface
> * set_interface
> * new_key
> * start_ap
> * new_station
> * new_mpath
> * set_mesh_config
> * set_bss
> * authenticate
> * associate
> * deauthenticate
> * disassociate
> * join_ibss
> * join_mesh
> * set_tx_bitrate_mask
> * frame
> * frame_wait_cancel
> * set_wiphy_netns
> * set_channel
> * set_wds_peer
> * probe_client
> * set_noack_map
> * register_beacons
> * start_p2p_device
> * set_mcast_rate
> * Unknown command (104)
> * connect
> * disconnect
> Supported TX frame types:
> * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0
> 0xd0 0xe0 0xf0
> * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0
> 0xc0 0xd0 0xe0 0xf0
> * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0
> 0xd0 0xe0 0xf0
> * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0
> 0xc0 0xd0 0xe0 0xf0
> * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0
> 0xc0 0xd0 0xe0 0xf0
> * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0
> 0xc0 0xd0 0xe0 0xf0
> * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0
> 0xd0 0xe0 0xf0
> * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0
> 0xc0 0xd0 0xe0 0xf0
> Supported RX frame types:
> * IBSS: 0x40 0xb0 0xc0 0xd0
> * managed: 0x40 0xd0
> * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
> * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
> * mesh point: 0xb0 0xc0 0xd0
> * P2P-client: 0x40 0xd0
> * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
> * P2P-device: 0x40 0xd0
> WoWLAN support:
> * wake up on disconnect
> * wake up on magic packet
> * wake up on pattern match, up to 20 patterns of 16-128 bytes,
> maximum packet offset 0 bytes
> * can do GTK rekeying
> * wake up on GTK rekey failure
> * wake up on EAP identity request
> * wake up on rfkill release
> software interface modes (can always be added):
> * AP/VLAN
> * monitor
> valid interface combinations:
> * #{ managed } <= 1, #{ AP } <= 1,
> total <= 2, #channels <= 1, STA/AP BI must match
> * #{ managed } <= 2,
> total <= 2, #channels <= 1
> HT Capability overrides:
> * MCS: ff ff ff ff ff ff ff ff ff ff
> * maximum A-MSDU length
> * supported channel width
> * short GI for 40 MHz
> * max A-MPDU length exponent
> * min MPDU start spacing
> Device supports TX status socket option.
> Device supports HT-IBSS.
> Device supports scan flush.
>
>
> try the following file but does not work
>
> [connection]
> id=Hotspot
> uuid=e231df45-4d5f-40d9-8dca-8244ace44eeb
> type=wifi
> autoconnect=false
>
> [wifi]
> ssid=NZ@McD1
> mode=ap
> mac-address=4C:80:93:97:40:EB
> security=802-11-wireless-security
> hidden=true
>
> [wifi-security]
> key-mgmt=none
>
> [ipv4]
> method=shared
>
> [ipv6]
> method=auto
>
> if anyone knows any solution thank you
_______________________________________________
networkmanager-list mailing list
networkmanager-list@gnome.org
https://mail.gnome.org/mailman/listinfo/networkmanager-list
