Dennis,
Thank you very much for your kind reply.
I reinstalled Mandrake 9.0 and at least this time the CDR was
auto-detected with 'cdrecord -scandisk' as on 0,3,0.
However it still will not work, due to the following error messages from
both X-CD-Roast and the cdrecord command line as follows:-
cdrecord: Trying to use high speed medium on low speed writer.
The 'cdrecord -scanbus' followed by the 'cdrecord' command line
follows:-
[root@localhost malcolm]# cdrecord -scanbus
Cdrecord 1.11a32 (i586-mandrake-linux-gnu) Copyright (C) 1995-2002 J�rg
Schilling
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.6'
scsibus0:
0,0,0 0) *
0,1,0 1) *
0,2,0 2) *
0,3,0 3) 'MITSUMI ' 'CR-4804TE ' '2.6C' Removable
CD-ROM
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *
[root@localhost malcolm]# cdrecord -v speed=4 dev=0,3,0 -isosize
mtdir-25oct02.raw
Cdrecord 1.11a32 (i586-mandrake-linux-gnu) Copyright (C) 1995-2002 J�rg
Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,3,0'
scsibus: 0 target: 3 lun: 0
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.6'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'MITSUMI '
Identifikation : 'CR-4804TE '
Revision : '2.6C'
Device seems to be: Philips CDD-522.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO
Supported modes: TAO PACKET RAW/R16 RAW/R96R
Drive buf size : 1343488 = 1312 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 164 MB padsize: 30 KB
Total size: 188 MB (18:41.08) = 84081 sectors
Lout start: 188 MB (18:43/06) = 84081 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 3
Reference speed: 6
Is not unrestricted
Is erasable
Disk sub type: High speed Rewritable (CAV) media (1)
ATIP start of lead in: -11745 (97:25/30)
ATIP start of lead out: 359848 (79:59/73)
speed low: 4 speed high: 8
power mult factor: 1 5
recommended erase/write power: 5
A2 values: 26 B2 4A
Disk type: Phase change
Manuf. index: 40
Manufacturer: INFODISC Technology Co., Ltd.
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 275767
cdrecord: Trying to use high speed medium on low speed writer.
cdrecord: fifo had 0 puts and 0 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 0%.
[root@localhost malcolm]#
The machine has a Celeron 500 chip with 128 mg ram and 198 swap space.
Any comments will be very much appreciated.
Kind regards,
Malcolm Candlish.
On Fri, 2002-10-25 at 19:31, Dennis Myers wrote:
> On Friday 25 October 2002 01:09 pm, Malcolm Candlish wrote:
> > Sirs,
> >
> > I have a Mitsumi CR-4804TE with which I had hoped to Burn Linux CD's.
> >
> > It's an ide-scsi type. Set it up via the HOWTO and not only does it not
> > work, my scsi scanner no longer operates either.
> >
> > Mandrake Control Center seems of little value unless it finds dev via
> > its own scan.
> >
> > Anyone else had this problem?
> >
> > Malcolm Candlish.
> Which OS are you using? MandrakeLinux 8.2, 9.0? I have the same burner and it
> works very well. It was autodetected and set up during install. Give us
> some details and/or error messages to go by, a solution is on the list. : )
> --
> Dennis M. linux user #180842
>
> ----
>
> Want to buy your Pack or Services from MandrakeSoft?
> Go to http://www.mandrakestore.com
Want to buy your Pack or Services from MandrakeSoft?
Go to http://www.mandrakestore.com
