-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi H.J.Bathoorn,
On Wednesday, November 19, 2003, at 12:45:43 PM PST, you wrote:
> I just noticed in your mail that sis900 is mentioned as eth0 as well
> as eth1....that could be your problem.
> Open a terminal, become su/root and type "ifconfig". If the output
> only mentions "lo" there's no internet or lan configured and you'll
> have to reconfigure:p
> If there is more: send us the output. As well as the output of
> "route" (still as su/root).
> If your connection is OK eth0 (or maybe 1) should be there and so
> should route define a default gateway and the eth device it is
> connected to.
Okay...here's the output of my bumbling (I wasn't sure if
"reconfigure:p" was one or two commands, but as you can see here, it
didn't do anything as a single command):
[EMAIL PROTECTED] melissa]$ su
Password:
[EMAIL PROTECTED] melissa]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:6E:84:4B:35
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5 errors:0 dropped:0 overruns:0 frame:0
TX packets:11 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:1428 (1.3 Kb) TX bytes:2262 (2.2 Kb)
Interrupt:3 Base address:0x9800
eth0:9 Link encap:Ethernet HWaddr 00:0C:6E:84:4B:35
inet addr:127.255.255.255 Bcast:127.255.255.255
Mask:255.0.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:3 Base address:0x9800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:70 errors:0 dropped:0 overruns:0 frame:0
TX packets:70 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4608 (4.5 Kb) TX bytes:4608 (4.5 Kb)
[EMAIL PROTECTED] melissa]# reconfigure:p
bash: reconfigure:p: command not found
[EMAIL PROTECTED] melissa]# reconfigure:p
bash: reconfigure:p: command not found
[EMAIL PROTECTED] melissa]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref
Use Iface
127.0.0.0 * 255.0.0.0 U 0 0
0 lo
[EMAIL PROTECTED] melissa]#
Hmmm. Now what?
By the way...I did download the six bugfix RMPs for "drakxtools" and
"harddrake" that I mentioned in my other post, and burned them to
CD-R. How do I then install these into Mandrake? I tried to do it via
Konqueror (/cd... then select all/open with.../installation...), but
that didn't seem to work.
Thanks!
- --
Melissa
PGP public keys:
mailto:[EMAIL PROTECTED]&Body=Please%20send%20keys
-----BEGIN PGP SIGNATURE-----
iD8DBQE/u97vjVbXUvsE8ukRAqQPAKDmOxHLJaMTX96+GIfTwL0Ze6ybzwCfeOst
oKDLBGRuXkElhx/pJYcWY9w=
=UQoC
-----END PGP SIGNATURE-----
Want to buy your Pack or Services from MandrakeSoft?
Go to http://www.mandrakestore.com
