Hello,
my cursor is good now (i add the option "swcursor" in my XF86config-4) but the display
always be bad.
I give you my XF86config-4 and my XFree86.0.log... this may help you to help me...
A lot of thanks for your answers...
Benjamin
>>> [EMAIL PROTECTED] samedi 6 avril 2002 18:36:19 >>>
Would this by any chance be a Compaq Deskpro 4000? Your problem seems similar to one
that I had with that machine and its OEM version of the S3 Virge GX card which, as I
recall, used the same chip.
The solution: use XFree86 version 3.3.6 rather than 4.x.x. Here is what worked for
my installation of Redhat 7.2. (Posted Previously)
Regarding Deskpro (4000?) using S3 ViRGE GX. I have just gone through the same
experience. I am installing RedHat 7.2.
My symptoms were a small, rectangular area that adjacent to the cursor, plus other
annoying distortions. I was using a SonyCPD 1304 monitor that was supported by
RedHat..
I found the solution at "www.dsm.fordham.edu/~moniot/linux-compaq/". With RedHat's
help I was able to implement it.
The basic problem seems to be that the XF86_SVGA server doesn't support Compaq's (OEM
version?) of the S3 Virge card It is better supported by the XF86_S3 server which was
also included on the RedHat distribution disks.
To implement I had to do the following:
Mount RedHat Installation CD # 2
Goto ...../RedHat/RPMS/ directory on CD # 2
rpm -ivh XFree86-S3V* (Install the needed server on my hard drive)
Xconfigurator --expert --preferxf3 --server XF86_S3V (Run the configuration
program)
During Xconfigurator:
Choose the S3V driver during the Xconfigurator process. (I think it was the
next-to-last listed driver, but I could be wrong about both its name and its location
in the list. )
No preference for RAMDAC and Clock during Xconfigurator.
When it was done the Xconfig file contained entries for "My Video Card" in the device
and screen sections.
At www.dsm.fordham.edu/~moniot/linux-compaq/ the author said a link needed to be added:
"ln -fs /usr/X11R6/bin/XF86_S3V /etc/X11/X"
I didn't need to do this to get it to work. I think Xconfigurator created the link as
there is an /etc/X11/X file on my system. (Of course there was one before, so I don't
know for sure.)
One glitch remains: After exiting Xwindow the command line text screen is garbled.
The author at
www.dsm.fordham.edu/~moniot/linux-compaq/ says there is a program, vga_reset, that
will correct that problem. I haven't been able to find that program, so I cannot
confirm it will work.
If you know how to get vga_reset (supposedly included in Desbian Distribution) let me
know.
Message: 6
Date: Fri, 05 Apr 2002 10:10:50 +0200
From: "Benjamin GOURLAT" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Subject: [Newbie]a problem with a S3 video card
Reply-To: [EMAIL PROTECTED]
This is a multipart message in MIME format
--------------InterScan_NT_MIME_Boundary
Content-Type: text/plain; charset=US-ASCII
Content-Transfer-Encoding: quoted-printable
Content-Disposition: inline
hello all,
I've got a computer with a video card based on a S3 chip "86C385".=20
This video card works with Windows NT4 so i need to install Linux Mandrake =
8.2... I install it without any problem for choose my option and install =
all the packages but when i try to install the video for Xfree 4... I =
begin to have problems : my cursor have a big shadow and my display was =
not clean...
I try to find a solution on Google without any result who help me....=20
Thanks for your help
Bye
Benjamin GOURLAT from FRANCE :)
_______________________________________________
Newbie mailing list
[EMAIL PROTECTED]
*** To unsubscribe , or change message options, see:
http://XFree86.Org/mailman/listinfo/newbie
XFree86 Version 4.2.0 / X Window System
(protocol Version 11, revision 0, vendor release 6600)
Release Date: 23 January 2002
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See http://www.XFree86.Org/)
Build Operating System: Linux 2.4.18-1mdksmp i686 [ELF]
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Tue Apr 9 12:17:13 2002
(==) Using config file: "/etc/X11/XF86Config-4"
(==) ServerLayout "layout1"
(**) |-->Screen "screen1" (0)
(**) | |-->Monitor "Sony|Sony Multiscan 15sf"
(**) | |-->Device "S3 ViRGE/GX (generic)"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard1"
(**) Option "AutoRepeat" "250 30"
(**) Option "XkbRules" "xfree86"
(**) XKB: rules: "xfree86"
(**) Option "XkbModel" "pc105"
(**) XKB: model: "pc105"
(**) Option "XkbLayout" "fr"
(**) XKB: layout: "fr"
(==) Keyboard: CustomKeycode disabled
(**) FontPath set to "unix/:-1"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(**) Option "AllowMouseOpenFail"
(--) using VT number 7
(WW) Open APM failed (/dev/apm_bios) (No such file or directory)
(II) Module ABI versions:
XFree86 ANSI C Emulation: 0.1
XFree86 Video Driver: 0.5
XFree86 XInput driver : 0.3
XFree86 Server Extension : 0.1
XFree86 Font Renderer : 0.3
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.5
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,7100 card 0000,0000 rev 01 class 06,00,00 hdr 00
(II) PCI: 00:07:0: chip 8086,7110 card 0000,0000 rev 01 class 06,01,00 hdr 80
(II) PCI: 00:07:1: chip 8086,7111 card 0000,0000 rev 01 class 01,01,80 hdr 00
(II) PCI: 00:07:2: chip 8086,7112 card 0000,0000 rev 01 class 0c,03,00 hdr 00
(II) PCI: 00:07:3: chip 8086,7113 card 0000,0000 rev 01 class 06,80,00 hdr 00
(II) PCI: 00:08:0: chip 5333,8a01 card 0000,0000 rev 01 class 03,00,00 hdr 00
(II) PCI: 00:12:0: chip 10b7,9000 card 0000,0000 rev 00 class 02,00,00 hdr 00
(II) PCI: End of PCI scan
(II) LoadModule: "scanpci"
(II) Loading /usr/X11R6/lib/modules/libscanpci.a
(II) Module scanpci: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.5
(II) UnloadModule: "scanpci"
(II) Unloading /usr/X11R6/lib/modules/libscanpci.a
(II) Host-to-PCI bridge:
(II) PCI-to-ISA bridge:
(II) Bus 0: bridge is at (0:0:0), (-1,0,0), BCTRL: 0x08 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1: bridge is at (0:7:0), (0,-1,0), BCTRL: 0x08 (VGA_EN is set)
(II) Bus -1 I/O range:
(II) Bus -1 non-prefetchable memory range:
(II) Bus -1 prefetchable memory range:
(--) PCI:*(0:8:0) S3 ViRGE/DX or /GX rev 1, Mem @ 0xf8000000/26
(II) Addressable bus resource ranges are
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0x00000000 - 0x000000ff (0x100) IX[B]
(II) Active PCI resource ranges:
[0] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[1] -1 0x0000fcc0 - 0x0000fcff (0x40) IX[B]
[2] -1 0x0000fca0 - 0x0000fcbf (0x20) IX[B]
[3] -1 0x0000fc90 - 0x0000fc9f (0x10) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[1] -1 0x0000fcc0 - 0x0000fcff (0x40) IX[B]
[2] -1 0x0000fca0 - 0x0000fcbf (0x20) IX[B]
[3] -1 0x0000fc90 - 0x0000fc9f (0x10) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[6] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[7] -1 0x00000000 - 0x000000ff (0x100) IX[B]
[8] -1 0x0000fcc0 - 0x0000fcff (0x40) IX[B]
[9] -1 0x0000fca0 - 0x0000fcbf (0x20) IX[B]
[10] -1 0x0000fc90 - 0x0000fc9f (0x10) IX[B]
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.1
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.a
(II) Module freetype: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.1.10
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font FreeType
(II) LoadModule: "s3virge"
(II) Loading /usr/X11R6/lib/modules/drivers/s3virge_drv.o
(II) Module s3virge: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.8.3
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.5
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
Module class: XFree86 XInput Driver
ABI class: XFree86 XInput driver, version 0.3
(II) S3VIRGE: driver (version 1.8.3) for S3 ViRGE chipsets: virge, 86C325,
virge vx, 86C988, virge dx, virge gx, 86C375, 86C385, virge gx2,
86C357, virge mx, 86C260, virge mx+, 86C280, trio 3d, 86C365,
trio 3d/2x, 86C362, 86C368
(II) Primary Device is: PCI 00:08:0
(--) Assigning device section with no busID to primary device
(--) Chipset virge dx found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[6] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[7] -1 0x00000000 - 0x000000ff (0x100) IX[B]
[8] -1 0x0000fcc0 - 0x0000fcff (0x40) IX[B]
[9] -1 0x0000fca0 - 0x0000fcbf (0x20) IX[B]
[10] -1 0x0000fc90 - 0x0000fc9f (0x10) IX[B]
(II) resource ranges after probing:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[6] 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[7] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[8] 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[9] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[10] -1 0x00000000 - 0x000000ff (0x100) IX[B]
[11] -1 0x0000fcc0 - 0x0000fcff (0x40) IX[B]
[12] -1 0x0000fca0 - 0x0000fcbf (0x20) IX[B]
[13] -1 0x0000fc90 - 0x0000fc9f (0x10) IX[B]
[14] 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[15] 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.5
(**) S3VIRGE(0): Depth 16, (--) framebuffer bpp 16
(==) S3VIRGE(0): RGB weight 565
(==) S3VIRGE(0): Default visual is TrueColor
(**) S3VIRGE(0): Option "SWCursor"
(**) S3VIRGE(0): Using SW Cursor
(==) S3VIRGE(0): Using fb.
(==) S3VIRGE(0): mx_cr3a_fix.
(==) S3VIRGE(0): XVideo allowed (depends on chipset).
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.5
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/linux/libint10.a
(II) Module int10: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.5
(II) S3VIRGE(0): initializing int10
(II) S3VIRGE(0): Primary V_BIOS segment is: 0xc000
(II) S3VIRGE(0): VESA BIOS detected
(II) S3VIRGE(0): VESA VBE Version 2.0
(II) S3VIRGE(0): VESA VBE Total Mem: 2048 kB
(II) S3VIRGE(0): VESA VBE OEM: S3 Incorporated. ViRGE /DX /GX
(II) S3VIRGE(0): VESA VBE OEM Software Rev: 1.1
(II) S3VIRGE(0): VESA VBE OEM Vendor: S3 Incorporated.
(II) S3VIRGE(0): VESA VBE OEM Product: ViRGE /DX /GX
(II) S3VIRGE(0): VESA VBE OEM Product Rev: Rev B
(--) S3VIRGE(0): Chipset: "virge dx"
(WW) System lacks support for changing MTRRs
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.5
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) S3VIRGE(0): VESA VBE DDC supported
(II) S3VIRGE(0): VESA VBE DDC Level 2
(II) S3VIRGE(0): VESA VBE DDC transfer in appr. 1 sec.
(II) S3VIRGE(0): VESA VBE DDC read successfully
(II) S3VIRGE(0): Manufacturer: SNY Model: 0 Serial#: 0
(II) S3VIRGE(0): Year: 1995 Week: 50
(II) S3VIRGE(0): EDID Version: 1.0
(II) S3VIRGE(0): Analog Display Input, Input Voltage Level: 0.714/0.286 V
(II) S3VIRGE(0): Sync: Separate Composite SyncOnGreen
(II) S3VIRGE(0): Max H-Image Size [cm]: horiz.: 29 vert.: 21
(II) S3VIRGE(0): Gamma: 2.86
(II) S3VIRGE(0): DPMS capabilities: Suspend Off; RGB/Color Display
(II) S3VIRGE(0): redX: 0.625 redY: 0.340 greenX: 0.280 greenY: 0.595
(II) S3VIRGE(0): blueX: 0.155 blueY: 0.070 whiteX: 0.283 whiteY: 0.298
(II) S3VIRGE(0): Supported VESA Video Modes:
(II) S3VIRGE(0): 640x480@60Hz
(II) S3VIRGE(0): 800x600@75Hz
(II) S3VIRGE(0): 832x624@75Hz
(II) S3VIRGE(0): 1024x768@75Hz
(II) S3VIRGE(0): Manufacturer's mask: 0
(II) S3VIRGE(0): Supported Future Video Modes:
(II) S3VIRGE(0): #0: hsize: 800 vsize 600 refresh: 85 vid: 22853
(II) S3VIRGE(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(==) S3VIRGE(0): Using gamma correction (1.0, 1.0, 1.0)
(--) S3VIRGE(0): videoram: 2048k
(--) S3VIRGE(0): Detected current MCLK value of 66.222 MHz
(II) S3VIRGE(0): Sony|Sony Multiscan 15sf: Using hsync range of 31.00-64.00 kHz
(II) S3VIRGE(0): Sony|Sony Multiscan 15sf: Using vrefresh range of 50.00-120.00 Hz
(II) S3VIRGE(0): Clock range: 20.00 to 270.00 MHz
(II) S3VIRGE(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1152x864" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1280x960" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1280x960" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1280x1024" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1280x1024" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1280x1024" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1400x1050" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1400x1050" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1024" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan)
(--) S3VIRGE(0): Virtual size is 800x600 (pitch 800)
(**) S3VIRGE(0): Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz
(II) S3VIRGE(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync
+vsync
(**) S3VIRGE(0): Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz
(II) S3VIRGE(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync
-vsync
(--) S3VIRGE(0): Display dimensions: (290, 210) mm
(--) S3VIRGE(0): DPI set to (70, 72)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.1
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="The XFree86 Project"
compiled for 4.2.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.5
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0xf8000000 - 0xfbffffff (0x4000000) MS[B]
[1] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[2] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[3] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[4] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[5] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[6] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[7] 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
[8] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
[9] 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
[10] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0x0000fcc0 - 0x0000fcff (0x40) IX[B]
[13] -1 0x0000fca0 - 0x0000fcbf (0x20) IX[B]
[14] -1 0x0000fc90 - 0x0000fc9f (0x10) IX[B]
[15] 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[16] 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(**) S3VIRGE(0): Using FB
(II) S3VIRGE(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
CPU to Screen color expansion
Solid Horizontal and Vertical Lines
Image Writes
Offscreen Pixmaps
Setting up tile and stipple cache:
30 128x128 slots
(==) S3VIRGE(0): Backing store disabled
(==) S3VIRGE(0): Silken mouse enabled
(II) S3VIRGE(0): Using overlay video
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(**) Option "Protocol" "PS/2"
(**) Mouse1: Protocol: "PS/2"
(**) Option "CorePointer"
(**) Mouse1: Core Pointer
(**) Option "Device" "/dev/psaux"
(**) Option "Emulate3Buttons"
(**) Option "Emulate3Timeout" "50"
(**) Mouse1: Emulate3Buttons, Emulate3Timeout: 50
(==) Mouse1: Buttons: 3
(II) Keyboard "Keyboard1" handled by legacy driver
(II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE)
# File generated by XFdrake.
# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Mandrake 6.0 and later now use a font server independent of
# the X server to render fonts.
FontPath "unix/:-1"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
#NoTrapSignals
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
#DontZap
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
#DontZoom
# This allows the server to start up even if the
# mouse device can't be opened/initialised.
AllowMouseOpenFail
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Keyboard section
# **********************************************************************
Section "InputDevice"
Identifier "Keyboard1"
Driver "Keyboard"
Option "AutoRepeat" "250 30"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "fr"
EndSection
# **********************************************************************
# Pointer section
# **********************************************************************
Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "PS/2"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons"
Option "Emulate3Timeout" "50"
# ChordMiddle is an option for some 3-button Logitech mice
# Option "ChordMiddle"
EndSection
Section "Module"
# This loads the DBE extension module.
## Load "dbe"
# This loads the Video for Linux module.
## Load "v4l"
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
## SubSection "extmod"
## #Option "omit xfree86-dga"
## EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"
EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "Sony|Sony Multiscan 15sf"
VendorName "Sony"
ModelName "Unknown"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 31.0-64.0
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50.0-120.0
# This is a set of extended mode timings typically used for laptop,
# TV fullscreen mode or DVD fullscreen output.
# These are available along with standard mode timings.
# Sony Vaio C1(X,XS,VE,VN)?
# 1024x480 @ 85.6 Hz, 48 kHz hsync
ModeLine "1024x480" 65.00 1024 1032 1176 1344 480 488 494 563 -hsync -vsync
# 768x576 @ 79 Hz, 50 kHz hsync
ModeLine "768x576" 50.00 768 832 846 1000 576 590 595 630
# 768x576 @ 100 Hz, 61.6 kHz hsync
ModeLine "768x576" 63.07 768 800 960 1024 576 578 590 616
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
##Section "Device"
## Identifier "Generic VGA"
## Driver "vga"
##EndSection
Section "Device"
Identifier "S3 ViRGE/GX (generic)"
VendorName "Unknown"
BoardName "Unknown"
Driver "s3virge"
#Option "xaa_benchmark"
#Option "fifo_moderate"
#Option "pci_burst_on"
#Option "pci_retry"
# Clock lines
# Uncomment following option if you see a big white block
# instead of the cursor!
Option "sw_cursor"
##Option "DPMS" "on"
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
Section "Screen"
Identifier "screen1"
Device "S3 ViRGE/GX (generic)"
Monitor "Sony|Sony Multiscan 15sf"
DefaultColorDepth 16
Subsection "Display"
Depth 8
Modes "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 15
Modes "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 32
Modes "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection
Section "ServerLayout"
Identifier "layout1"
Screen "screen1"
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
****** Message from InterScan E-Mail VirusWall NT ******
** No virus found in attached file noname.htm
** No virus found in attached file XFree86.0.log
** No virus found in attached file XF86Config-4
AV/BorderMail un service anti-virus de AIC Network ( www.aic.fr)
***************** End of message ***************
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Ce message a �t� contr�l� par le service
anti-virus AV/BorderMail.
This mail is checked with AV/BorderMail
A virus scanning Service of
AIC Network - www.central-isp.com
vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
