It just so happens that I took apart and repaired the tach on my 85
450 yesterday, so I can give you some insight. (The following assumes
that the '82 tach functions the same as the '85 tach!) Firstly, there
is no fluid, just the magnet. The shaft goes in at an angle and the
magnet is on one side of it. The needle is attached to a "bowl" that
surrounds the spinning magnet so the force to the bowl is "pulsed" The
pulsing is damped by a simple coil spring. The problem I had was that
after a crash, I think the needle jumped the back stop and unwound by
one turn, so the readings were about 1.75 times high, not being
opposed by the same amount of force.

It sounds to me like you have one of two problems: one, the spring was
overwound by an overzealous repairer, which is possible but unlikely;
or two, you've just got crud in there. The needle is attached to a,
well, needle, which sits in a little brass pivot. If the pivot point
is dirty, I think it would cause the problems you mention.

As to disassembly, the whole thing is held together by a metal ring.
You should be able to get a flathead screwdriver in there and slowly
go around bending the back side of the ring out of shape until you can
remove the two halves of the housing. It will never look the same, but
if you're concerned about looks I suggest you get a new tachometer.
Anyway, once you get that ring off you can separate the three case
elements: the front, the back, and a middle piece that actually has
the face glass and a rubber gasket.

It's not a complicated piece of equipment, so as long as you pay
attention to what screws came out of where, you can break it down to
its individual pieces. Be especially careful with the spring: like I
said, it can be wound or unwound which will screw up the accuracy.
Give everything a thorough cleaning and reassemble. Use pliers to bend
the ring back into shape, reinstall, and let us know how it works.
Good luck!

Kevin P. Miller
1985 CB450SC

On Aug 21, 9:09 pm, Deano <[email protected]> wrote:
> Hi Nighthawk Group!
>
> Any suggestions on how to service the tachometer?  I'm looking at
> buying a 1982 CB450SC that has been brought back to life after 10+
> years in a garage. Today the seller and I replaced the fork seals and
> all looked good there. The tacho problem is that it is highly
> overdamped. Maybe it will show the correct RPM if you give it enough
> time to settle-out.  The seller commented that he didn't notice the
> problem until today b/c he's been riding it and not rapping on the
> throttle as much as a newbie like me did today. The cable seems to
> spin as fast as the motor turns it: no dragging.
>
> My understanding of mechanical tachos is that there's a small drum or
> magnets spinning in the tacho body and another drum or something with
> the needle attached that is concentric with the drum driven by the
> cable. The faster the driven drum spins, the more viscous (or
> magnetic) forces torque the second drum around and indicate a faster
> engine RPM. Knowing that the bike has been sitting around for years,
> I'm guessing that if there is some sort of fluid coupling between the
> drums and the fluid has all leaked out the coupling would be weak.
> This is all speculation since we were not able to get the tacho casing
> apart.
>
> Any suggestions?
>
> --Steve
--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups 
"Nighthawk Motorcycle Lovers!" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/nighthawk_lovers?hl=en
-~----------~----~----~----~------~----~------~--~---

Reply via email to