On 2018-02-05 03:47, Ben Skeggs wrote:
On Mon, Feb 5, 2018 at 12:19 PM, Danilo Krummrich
<danilokrummr...@dk-develop.de> wrote:
On 2018-02-05 02:39, Ben Skeggs wrote:
On 5 February 2018 at 11:37, Ben Skeggs <skeg...@gmail.com> wrote:
On 5 February 2018 at 11:22, Danilo Krummrich
<danilokrummr...@dk-develop.de> wrote:
On Gainward GTX 1070 routing any other SOR than SOR-1 to macro link
'G' (outp index 7) causes failures:
[ 6.712111] nouveau 0000:01:00.0: bus: MMIO read of 00000000
FAULT at
61c880 [ IBUS ]
[ 6.724888] nouveau 0000:01:00.0: disp: intr24 80000000
[ 8.716668] nouveau 0000:01:00.0: DRM: base-0: timeout
[ 10.716679] nouveau 0000:01:00.0: DRM: base-1: timeout
[ 63.511862] nouveau 0000:01:00.0: DRM: EVO timeout
As I'm not able to spot an issue in the driver, I suppose it's
firmware related.
Are you able to mail me /dev/dri/card0/vbios.rom from that, please?
I'd like to look into this some more and be 100% certain this is
indeed a quirk, and not some subtle driver bug.
Err.. /sys/kernel/debug/dri/0/vbios.rom rather ;)
Sure, that makes sense definitely, as I have checked
gm200_sor_route_set and
gm200_sor_route_get only to conform to the statements in this mail
thread:
https://lists.freedesktop.org/archives/nouveau/2014-December/019408.html
BTW, I can reproduce the problem with a two monitor setup only, as (of
course) having one
monitor only at the physical port macro link 'G' is attached to makes
to
vbios pick the
working SOR. Therefore the physical port macro link 'G' is attached to
must
not be picked
as primary monitor.
Thanks for that. I've only had a quick look so far, but I'm going to
guess the is a driver bug already. The DCB specifies two different
outputs on pad macro 1 (which, would be SOR1 if identity-mapped) that
First of all, sorry for confusing with the macro link numeration.
Of course, I am talking about pad macro 1, link 2 (which is also called
macro link D). I was wrongly looking at outp->index.
I will send an updated patch series correcting this, just in case.
can apparently be used together. If used at the same time though,
they both can't be driven by the same SOR, and would need routing.
I agree that there's definitely the need of routing here. Anyway, it
can still be it's just buggy in a way that only macro link D cannot be
routed to a different SOR than SOR-1. Probably you know better, if such
a case can be possible.
I guess it'd be interesting to see if NVIDIA can manage to drive those
two outputs together, which would be a big hint as to whether the
board is buggy, or we are. I'm going to guess the latter ;)
I tested that - even nouveau is able to drive macro link C and D
together.
Macro link C corresponds to connector 3 (which is HDMI) and macro link D
corresponds to connector 4 (which is DP). And it actually works because
VBIOS
serves macro link D as primary OR and routes SOR-1 to it already.
Nouveau picks (of course) SOR-0 for macro link C then.
BTW, any other combination works well, as long as macro link D (if used)
is
not routed to another SOR than SOR-1. E.g. macro link A on SOR-2 and
macro
link E on either SOR-0 or SOR-3.
Also, may I ask you a related question: I was a bit confused why
'link' is
completely unused
in nvkm_outp_init_route() after gm200_sor_route_get() returns. Is this
just
obsolete or
intended to use in the future somehow?
I suspect it's a left-over from an earlier revision of that code, or
perhaps I intended to validate it against what we discovered? Not
sure now!
Thanks,
Ben.
Thanks,
Danilo
Thanks,
Ben.
Therefore to work around this issue skip crossbar routing for this
particular macro link and instead use identity mapping.
Signed-off-by: Danilo Krummrich <danilokrummr...@dk-develop.de>
---
drivers/gpu/drm/nouveau/nvkm/engine/device/pci.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/nouveau/nvkm/engine/device/pci.c
b/drivers/gpu/drm/nouveau/nvkm/engine/device/pci.c
index d2f9664afcf4..29de270f2232 100644
--- a/drivers/gpu/drm/nouveau/nvkm/engine/device/pci.c
+++ b/drivers/gpu/drm/nouveau/nvkm/engine/device/pci.c
@@ -797,6 +797,13 @@ nvkm_device_pci_10de_139b[] = {
{}
};
+static const struct nvkm_device_pci_vendor
+nvkm_device_pci_10de_1b81[] = {
+ /* Gainward GTX 1070 8192 MB */
+ { 0x10b0, 0x1b81, "GeForce GTX 1070",{ .outp_links_skip =
BIT(7)
} },
+ {}
+};
+
static const struct nvkm_device_pci_device
nvkm_device_pci_10de[] = {
{ 0x0020, "RIVA TNT" },
@@ -1556,7 +1563,7 @@ nvkm_device_pci_10de[] = {
{ 0x1b06, "GeForce GTX 1080 TI" },
{ 0x1bb7, "Quadro P6000" },
{ 0x1b80, "GeForce GTX 1080" },
- { 0x1b81, "GeForce GTX 1070" },
+ { 0x1b81, "GeForce GTX 1070", nvkm_device_pci_10de_1b81 },
{ 0x1b82, "GeForce GTX 1070 TI" },
{ 0x1b84, "GeForce GTX 1060 3GB" },
{ 0x1b87, "P104-100" },
--
2.14.1
_______________________________________________
Nouveau mailing list
Nouveau@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/nouveau
_______________________________________________
dri-devel mailing list
dri-de...@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
dri-devel mailing list
dri-de...@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
Nouveau mailing list
Nouveau@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/nouveau
