At 03:34 PM 6/10/2002 +0100, Randall Skelton wrote:
>Thanks Bill. I didn't realize that it was your site that I have been
>reading all morning ;)
>
>I now have the font example working... whew! I do see a large number of
>warnings of the form, "Warning: pdfetex (file
>/Users/mek/Local/texmf/pdftex/config/context/pl0-am s-cmr.map): entry for
>`plb10' already exists, duplicates ignored," but I get the correct fonts
>in the end. Should I see these warnings?
>
>My problem was simply that I became confused when I found two occurances
>of 'cont-sys':
the idea is that you rename one of them into cont-sys.tex and still have
the original
>--- Start type-banshee.tex
>%
>% Adobe Banshee
>%
>\usetypescriptfile[type-buy]
^^ not in this banshee file, but in your main doc
the idea behind typescript files is that they are parsed at runtime an
donly the info needed is picked up
btw, here i name those additional (user) typescript files typeface.tex, and
they normally reside in the project path
>\loadmapfile[texnansi-adobe-banshee.map]
>\starttypescript [serif] [banshee] [texnansi]
> \definefontsynonym [Banshee-Roman] [texnansi-banshee] [encoding=texnansi]
> \definefontsynonym [Banshee-Bold] [texnansi-banshee] [encoding=texnansi]
> \definefontsynonym [Banshee-Italic] [texnansi-banshee] [encoding=texnansi]
> \definefontsynonym [Banshee-Bold-Italic] [texnansi-banshee]
> [encoding=texnansi]
>\stoptypescript
>
>\starttypescript [serif] [charter] [name]
> \usetypescript[serif][fallback]
^^^ needed ?
> \definefontsynonym [Serif] [Banshee-Roman]
> \definefontsynonym [SerifBold] [Banshee-Bold]
> \definefontsynonym [SerifItalic] [Banshee-Italic]
> \definefontsynonym [SerifBoldItalic] [Banshee-Bold-Italic]
>\stoptypescript
>
>\starttypescript [Banshee]
> \definetypeface [MyBanshee] [rm] [serif] [banshee] [default]
> [encoding=texnansi]
>\stoptypescript
>--- End
>
>When I use the above and try make a simple document, I again do not get
>the font included in the resulting pdf.
the defs look ok to me
>--- Begin test.tex
>\usetypescriptfile[type-banshee]
>\usetypescript[Banshee]
>\setupbodyfont[MyBanshee]
>
>\starttext
>This is Banshee type.
>\stoptext
but ... is your type-banshee read (grep for type-ban in the log)
>[ snip 250+ lines of similar warnings ]
>^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
you can turn off loading of the defaults in the cont-sys file; it all
depends a bit on how your system is configures; the main reason for the
fuzz is that pdftex does not permit overloading (on the to do list after
which the messages will disappear)
you can probably safely comment the \preload... lines in cont-sys.tex
>Warning: pdfetex (file /Users/mek/Local/texmf/pdftex/config/context/origin
>al-youngryu-tx.map): entry for `rtcxbsso' already exists, duplicates ignored
>}
>Warning: pdfetex (file texnansi-bh-lucida.map): cannot open font map file
>
>Warning: pdfetex (file texnansi-itc-officina.map): cannot open font map file
>
>Warning: pdfetex (file texnansi-ff-meta.map): cannot open font map file
>
>Warning: pdfetex (file texnansi-linotype-univers.map): cannot open font
>map fil
>e
>
>Warning: pdfetex (file texnansi-itc-mendoza.map): cannot open font map file
>
>Warning: pdfetex (file texnansi-adobe-frutiger.map): cannot open font map file
>]
looks like you load all map files; this is not really needed, unless you
define fonts on page>1 because pdftex does not read map files after page one
Hans
-------------------------------------------------------------------------
Hans Hagen | PRAGMA ADE | [EMAIL PROTECTED]
Ridderstraat 27 | 8061 GH Hasselt | The Netherlands
tel: +31 (0)38 477 53 69 | fax: +31 (0)38 477 53 74 | www.pragma-ade.com
-------------------------------------------------------------------------
information: http://www.pragma-ade.com/roadmap.pdf
documentation: http://www.pragma-ade.com/showcase.pdf
-------------------------------------------------------------------------
