0100 please update to the latest SVN rev Regards Alfredo
On Feb 12, 2012, at 7:21 PM, 0100 wrote: > Please can someone help? > > On Friday, February 10, 2012, 0100 <[email protected]> wrote: > > Hi. > > > > I can't get two simultaneous daemons to listen on the same interface. > > After reading it seems like this is usually due to quick_mode being > > enabled but as far as I can tell I'm loading the kernel module with > > quick_mode off. Please help! > > > > # uname -a > > Linux 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:56:25 UTC 2011 > > x86_64 x86_64 x86_64 GNU/Linux > > > > I'm loading the module as follows. > > # insmod /lib/modules/3.0.0-12-generic/kernel/net/pf_ring/pf_ring.ko > > quick_mode=0 > > > > # modinfo pf_ring > > filename: /lib/modules/3.0.0-12-generic/kernel/net/pf_ring/pf_ring.ko > > alias: net-pf-27 > > description: Packet capture acceleration and analysis > > author: Luca Deri <[email protected]> > > license: GPL > > srcversion: 0702EEDDBCDB46025A6CC28 > > depends: > > vermagic: 3.0.0-12-generic SMP mod_unload modversions > > parm: min_num_slots:Min number of ring slots (uint) > > parm: transparent_mode:0=standard Linux, > > 1=direct2pfring+transparent, 2=direct2pfring+non transparentFor 1 and > > 2 you need to use a PF_RING aware driver (uint) > > parm: enable_debug:Set to 1 to enable PF_RING debug tracing > > into the syslog (uint) > > parm: enable_tx_capture:Set to 1 to capture outgoing packets > > (uint) > > parm: enable_ip_defrag:Set to 1 to enable IP > > defragmentation(only rx traffic is defragmentead) (uint) > > parm: quick_mode:Set to 1 to run at full speed but with upto > > one socket per interface (uint) > > > > # cat /proc/net/pf_ring/info > > PF_RING Version : 5.2.3 ($Revision: 5164$) > > Ring slots : 4096 > > Slot version : 13 > > Capture TX : Yes [RX+TX] > > IP Defragment : No > > Socket Mode : Standard > > Transparent mode : Yes (mode 0) > > Total rings : 1 > > Total plugins : 0 > > > > # cat /proc/net/pf_ring/dev/eth2/info > > Name: eth2 > > Index: 2 > > Address: 68:05:CA:01:90:18 > > Polling Mode: NAPI/TNAPI > > Type: Ethernet > > Family: Standard NIC > > # Bound Sockets: 1 > > Max # TX Queues: 1 > > # Used RX Queues: 1 > > > > When I have one pfcount session already running, then I can't start another > > one: > > > > # ./pfcount -i eth2 > > pfring_set_channel_id() failed: -1 > > pfring_open error [Invalid argument] (pf_ring not loaded or perhaps > > you use quick mode and have already a socket bound to eth2 ?) > > > > > > Thanks! > > _______________________________________________ > Ntop-misc mailing list > [email protected] > http://listgateway.unipi.it/mailman/listinfo/ntop-misc
_______________________________________________ Ntop-misc mailing list [email protected] http://listgateway.unipi.it/mailman/listinfo/ntop-misc
