I'm using the March 19 snapshot and having problems when using ntop and SSL.
the box: PIII 750Mhz 512 MB RAM RH Linux kernel 2.4.7-10 gcc v2.96 the rest is in the dmesg below. command line usage is: ./ntop -W 3001 -p ./home/ntopdb First the easy question, after looking through man pages and FAQs, I can't find the command line flag to enable tracking of open TCP sessions... what is it? The problem: When I use the SSL connection (https://myserver:3001), none of the pie charts or bar graphs show up. When using http://myserver:3000 though, everything shows up just fine, no problems and all the charts and graphs work. When building ntop, I follow the instructions in the build file, with the exception of the final step: ./autogen.sh -1 ./configure make make install (Thanks to Burton for the two extra steps!) ideas? Dan Norton Linux version 2.4.7-10 ([EMAIL PROTECTED]) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-98)) #1 Thu Sep 6 17:27:27 EDT 2001 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable) BIOS-e820: 000000001ffc0000 - 000000001fff8000 (ACPI data) BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) Scanning bios EBDA for MXT signature On node 0 totalpages: 131008 zone(0): 4096 pages. zone(1): 126912 pages. zone(2): 0 pages. Kernel command line: auto BOOT_IMAGE=linux ro root=303 BOOT_FILE=/boot/vmlinuz-2.4.7-10 Initializing CPU#0 Detected 751.721 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1500.77 BogoMIPS Memory: 510516k/524032k available (1269k kernel code, 11064k reserved, 90k data, 220k init, 0k highmem) Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 8, 1048576 bytes) CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000 CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000 CPU: Common caps: 0383f9ff 00000000 00000000 00000000 CPU: Intel Pentium III (Coppermine) stepping 03 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED]) mtrr: detected mtrr type: Intel PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=0 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Using IRQ router PIIX [8086/7110] at 00:07.0 Limiting direct PCI/PCI transfers. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x0b (Driver version 1.14) mxt_scan_bios: enter Starting kswapd v1.8 VFS: Diskquotas version dquot_6.5.0 initialized pty: 2048 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10d block: queued sectors max/low 338973kB/207901kB, 1024 slots per queue RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller on PCI bus 00 dev 39 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:DMA hda: Maxtor 91366U4, ATA DISK drive hdd: CD-224E, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: 26588016 sectors (13613 MB) w/2048KiB Cache, CHS=1655/255/63, UDMA(33) ide-floppy driver 0.97 Partition check: hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 > Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 ide-floppy driver 0.97 md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 32768) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 319k freed VFS: Mounted root (ext2 filesystem). Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 220k freed Adding Swap: 1044184k swap-space (priority -1) usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.259 $ time 17:36:49 Sep 6 2001 usb-uhci.c: High bandwidth mode enabled PCI: Found IRQ 10 for device 00:07.2 usb-uhci.c: USB UHCI at I/O 0xef80, IRQ 10 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.251:USB Universal Host Controller Interface driver EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,3), internal journal kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,6), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,5), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[EMAIL PROTECTED]> and others PCI: Found IRQ 5 for device 00:0c.0 PCI: Sharing IRQ 5 with 00:0d.0 eth0: Intel Corporation 82557 [Ethernet Pro 100], 00:D0:B7:9A:40:76, IRQ 5. Board assembly 000000-000, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0x04f4518b). PCI: Found IRQ 5 for device 00:0d.0 PCI: Sharing IRQ 5 with 00:0c.0 eth1: Intel Corporation 82557 [Ethernet Pro 100] (#2), 00:D0:B7:9A:40:77, IRQ 5. Board assembly 000000-000, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0x04f4518b).> _______________________________________________ Ntop mailing list [EMAIL PROTECTED] http://listmanager.unipi.it/mailman/listinfo/ntop
