>> > This is not good... > Please, post the output of the actual driver with -DDDDD. That is: > > megatec_usb -a Unitek -DDDDD
[EMAIL PROTECTED]:~# megatec_usb -a Unitek -DDDDD Network UPS Tools 2.2.1- - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c) 2006, Alexander Gordeev (c) 2006-2007, Jon Gough (c) 2007 debug level is '5' Checking device (0000/0000) (005/001) - VendorID: 0000 - ProductID: 0000 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 005 Trying to match device Device does not match - skipping Checking device (0001/0000) (003/003) - VendorID: 0001 - ProductID: 0000 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 003 Trying to match device Device matches failed to claim USB device, trying 2 more time(s)... detaching kernel driver from USB device... trying again to claim USB device... get_data_krauler: no command set Starting UPS detection process... Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 234.0 000 50.0 28.0 00.0 00001010 Q1 => OK [(234.0 165.0 234.0 000 50.0 28.0 00.0 00001010] Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 231.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(231.0 165.0 231.0 000 50.2 28.0 00.0 00001010] Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 237.0 000 50.0 28.0 00.0 00001010 Q1 => OK [(237.0 165.0 237.0 000 50.0 28.0 00.0 00001010] Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] - Unable to fetch string 3 get_data_krauler: connection failure Q1 => FAILED [timeout] Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 231.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(231.0 165.0 231.0 000 50.2 28.0 00.0 00001010] 1 out of 5 detection attempts failed (minimum failures: 2). Asking for UPS information [I]... get_data_krauler: index [0c], prefix [#] (len = 39/128)TEK ALPHA1250 VER2.0C I => OK [#UNITEK ALPHA1250 VER2.0C ] Megatec protocol UPS detected [UNITEK ALPHA1250 VER2.0C]. Parameter [ignoreoff]: [true] Asking for UPS power ratings [F]... get_data_krauler: index [0d], prefix [#] (len = 22/128).0 008 23.50 50.0 F => OK [#230.0 008 23.50 50.0] 23.5V battery, interval [21.3V, 27.1V]. - Unable to fetch string 11 Done setting up the UPS. Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 237.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(237.0 165.0 237.0 000 50.2 28.0 00.0 00001010] Calculated battery charge: 100.0% dstate_init: sock /var/state/ups/megatec_usb-Unitek open on fd 5 Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 231.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(231.0 165.0 231.0 000 50.2 28.0 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] -> String: UPS No Ack (len = 10/128) get_data_krauler: retry [UPS No Ack] -> String: UPS No Ack (len = 10/128) get_data_krauler: retry [UPS No Ack] - Unable to fetch string 3 get_data_krauler: connection failure Q1 => FAILED [timeout] Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 231.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(231.0 165.0 231.0 000 50.2 28.0 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 237.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(237.0 165.0 237.0 000 50.2 28.0 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 231.0 000 50.0 28.0 00.0 00001010 Q1 => OK [(231.0 165.0 231.0 000 50.0 28.0 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 231.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(231.0 165.0 231.0 000 50.2 28.0 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 237.0 000 50.0 28.0 00.0 00001010 Q1 => OK [(237.0 165.0 237.0 000 50.0 28.0 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 237.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(237.0 165.0 237.0 000 50.2 28.0 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 237.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(237.0 165.0 237.0 000 50.2 28.0 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... get_data_krauler: index [03], prefix [(] (len = 47/128).0 165.0 231.0 000 50.2 28.0 00.0 00001010 Q1 => OK [(231.0 165.0 231.0 000 50.2 28.0 00.0 00001010] Calculated battery charge: 100.0% And so it repeats until I stop it .... Regards Matt _______________________________________________ Nut-upsuser mailing list [email protected] http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser
