Hi, Back in December I posted this request :
http://lists.alioth.debian.org/pipermail/nut-upsuser/2007-December/003565.ht ml I have now tried version 2.2.2, which appears to give a slightly better ups.status of "OL OFF" Any further ideas - the UPS is on and connected to the load. Regards, Jason /usr/local/ups/bin/megatec_usb -a plexus -DD Network UPS Tools 2.2.2 - Megatec protocol driver 1.5.14 [megatec_usb] Carlos Rodrigues (c) 2003-2008 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c) 2006, Alexander Gordeev (c) 2006-2007, Jon Gough (c) 2007 debug level is '2' Checking device (0000/0000) (001/001) - VendorID: 0000 - ProductID: 0000 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 001 Trying to match device Device does not match - skipping Checking device (116F/C108) (002/003) - VendorID: 116f - ProductID: c108 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 002 Trying to match device Device does not match - skipping Checking device (0001/0000) (002/002) - VendorID: 0001 - ProductID: 0000 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 002 Trying to match device Device matches failed to claim USB device, trying 2 more time(s)... detaching kernel driver from USB device... trying again to claim USB device... Starting UPS detection process... Asking for UPS status [Q1]... Q1 => OK [(231.0 165.0 231.0 000 50.0 27.3 00.0 00001010] Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010] Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010] Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010] Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010] 0 out of 5 detection attempts failed (minimum failures: 2). Cancelling any pending shutdown or battery test. Asking for UPS information [I]... I => OK [# UPS1000V VER1.04 ] Megatec protocol UPS detected [ UPS1000V VER1.04]. Parameter [ignoreoff]: [false] Asking for UPS power ratings [F]... F => OK [#230.0 005 23.50 50.0] 23.5V battery, interval [21.3V, 27.1V]. Done setting up the UPS. Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010] Calculated battery charge: 100.0% dstate_init: sock /var/state/ups/megatec_usb-plexus open on fd 5 Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 49.8 27.3 00.0 00001010] Calculated battery charge: 100.0% Asking for UPS status [Q1]... Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010] Calculated battery charge: 100.0% Signal 2: exiting upsc plexus battery.charge: 100.0 battery.voltage: 27.30 battery.voltage.nominal: 23.5 driver.name: megatec_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.2.2 driver.version.internal: 1.5.14 input.frequency: 50.0 input.frequency.nominal: 50.0 input.voltage: 234.0 input.voltage.fault: 165.0 input.voltage.maximum: 243.0 input.voltage.minimum: 226.0 input.voltage.nominal: 230.0 output.voltage: 234.0 ups.beeper.status: disabled ups.delay.shutdown: 0 ups.delay.start: 2 ups.load: 0.0 ups.mfr: ups.model: UPS1000V VER1.04 ups.serial: unknown ups.status: OL OFF ups.type: standby _______________________________________________ Nut-upsuser mailing list [email protected] http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser
