Hi Vitor, thanks a lot for these info. I've just added it to the HCL of the Development version (r1989).
I would now be interested in having some more info: - a driver debug output to check some more things, ie: $ /path/to/megatec_usb -DDDDD -a eaton - the device USB VendorID and ProductID (as shown by lsusb) - when fully charged (ie online for some time), does battery.charge reaches 100 % ? otherwise, we'll have to use the battvolts parameter. depending on the answers to the above, we'll possibly have some more things to do. cheers, Arnaud -- Linux/Unix Expert R&D - Eaton - http://www.eaton.com/mgeops Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer - http://www.debian.org Free Software Developer - http://arnaud.quette.free.fr/ Le mardi 15 septembre 2009 à 00:07 -0300, Vitor Choi Feitosa a écrit : > Here's what you asked for: > > $ upsc eaton > battery.charge: 90.0 > battery.voltage: 13.30 > battery.voltage.nominal: 12.0 > driver.name: megatec_usb > driver.parameter.pollinterval: 2 > driver.parameter.port: auto > driver.version: 2.2.1- > driver.version.internal: 1.5.13 > input.frequency: 59.9 > input.voltage: 216.6 > input.voltage.fault: 216.6 > input.voltage.maximum: 222.7 > input.voltage.minimum: 206.0 > output.voltage: 216.6 > output.voltage.nominal: 230.0 > ups.beeper.status: enabled > ups.delay.shutdown: 0 > ups.delay.start: 2 > ups.load: 21.0 > ups.mfr: unknown > ups.model: unknown > ups.serial: unknown > ups.status: OL > ups.temperature: 25.0 > > > $ upscmd -l eaton > Instant commands supported on UPS [eaton]: > > test.battery.start.deep - Start a deep battery test > test.battery.start - Start a battery test > test.battery.stop - Stop the battery test > shutdown.return - Turn off the load and return when power is back > shutdown.stayoff - Turn off the load and remain off > shutdown.stop - Stop a shutdown in progress > load.on - Turn on the load immediately > load.off - Turn off the load immediately > reset.input.minmax - Reset minimum and maximum input voltage status > reset.watchdog - Reset watchdog timer > beeper.toggle - Toggle the UPS beeper > > > upsmon wall message > Broadcast Message from > n...@cctv > (somewhere) at > 12:15 ... > > > UPS ea...@localhost on battery > > > and finally, a syslog snippet of the system shutting down: > Sep 14 12:33:20 cctv upsd[6192]: Connection from 127.0.0.1 > Sep 14 12:33:20 cctv upsd[6192]: Client on 127.0.0.1 logged out > Sep 14 12:33:21 cctv upsmon[6200]: UPS ea...@localhost battery is low > Sep 14 12:33:21 cctv upsd[6192]: Client [email protected] set FSD on > UPS [eaton] > Sep 14 12:33:21 cctv upsmon[6200]: Executing automatic power-fail > shutdown > Sep 14 12:33:21 cctv upsmon[6200]: Auto logout and shutdown proceeding > Sep 14 12:33:22 cctv upsd[6192]: Connection from 127.0.0.1 > Sep 14 12:33:22 cctv upsd[6192]: Client on 127.0.0.1 logged out > Sep 14 12:33:24 cctv upsd[6192]: Connection from 127.0.0.1 > Sep 14 12:33:24 cctv upsd[6192]: Client on 127.0.0.1 logged out > Sep 14 12:33:26 cctv upsd[6192]: Host 127.0.0.1 disconnected (read > failure) > Sep 14 12:33:26 cctv init: tty4 main process (4901) killed by TERM > signal > Sep 14 12:33:26 cctv init: tty5 main process (4902) killed by TERM > signal > Sep 14 12:33:26 cctv init: tty2 main process (4904) killed by TERM > signal > Sep 14 12:33:26 cctv init: tty3 main process (4906) killed by TERM > signal > Sep 14 12:33:26 cctv init: tty1 main process (6445) killed by TERM > signal > Sep 14 12:33:26 cctv init: tty6 main process (4908) killed by TERM > signal > Sep 14 12:33:28 cctv avahi-daemon[5388]: Got SIGTERM, quitting. > > > Tell me if you need anything else. > > Vitor. > > > 2009/9/14 Arnaud Quette <[email protected]> > Le samedi 12 septembre 2009 à 01:59 -0300, Vitor Choi Feitosa > a écrit : > > Hi Arnaud, > > Hi Vitor, > > > I found your email on the contact page and since you seem to > work for > > Eaton and is involved in the NUT community I think you're > the right > > person to contact. > > > > I've got an Eaton NV 1000H and just installed it here. > Before NUT > > configuration I've checked the HCL for my UPS and didn't > find it > > there. After trying a few drivers I found that the > megatec_usb just > > works for this model. > > > > So.. I thought you could arrange to get this model on the > HCL. Will > > you do it? > > > sure. > > can you just post me the output of: > - upsc, > - upscmd, > - upsrw. > > Have you tested a standard shutdown (ie OB until LB, or > calling "upsmon > -c fsd")? > > thanks for your report. > Arnaud > -- > Linux/Unix Expert R&D - Eaton - http://www.eaton.com/mgeops > Network UPS Tools (NUT) Project Leader - > http://www.networkupstools.org/ > Debian Developer - http://www.debian.org > Free Software Developer - http://arnaud.quette.free.fr/ -------------------------------------------------------------------------- Eaton Power Quality SA ~ Siège social: 110 rue Blaise Pascal, 38 334 Saint Ismier, France ~ Lieu d'enregistrement au registre du commerce: Grenoble ~ Numéro d'enregistrement: 302 636 303 ~ Capital social souscrit et liberé: 703'802.75 EUR _______________________________________________ Nut-upsuser mailing list [email protected] http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser
