2010/3/14 IT Department ULQS <[email protected]>: > > I try send this email to '[email protected]' but: > Fri 2010-03-12 19:26:13: <-- 550-The account has been suspended > Fri 2010-03-12 19:26:13: <-- 550 A conta do destinatario encontra-se > suspensa (#5.1.1)
right, Carlos is retired from the NUT team. moreover the megatec and megatec_usb driver are obsolete, and replaced by blazer and blazer_usb. please, try blazer for further testing. and switch to NUT 2.4.3. > I hope you process the results of my work. > > > My UPS “Sinapse MSII6000” used megatec protocol on COM-port. > http://sinapse.ua/product/ups_sinapse/Sinapse/Sinapse_9103?cs_lang=ru > After some tunning it working with NUT. > ________________________________________ > > Value: > READ_PACE 300000 /* interval to wait between sending a command > and reading the response (usec) */ > to small for me and driver work not perfectly with my ups (frequently Q1 => > FAILED [short read] or other error) > > Especially is clearly seen in Check sub-procedure: /* Check for a > compatible UPS and for a reliable connection... */ with 5 frequently > request. > > I set it to 600000 usec and my problem go. > > May be put READ_PACE to config file ? It's best improvement. > __________________________________________ > > After this lines: > upsdebugx(1, "Cancelling any pending shutdown or battery test."); > ser_send_pace(upsfd, send_pace, "C%c", ENDCHAR); > need pause (READ_PACE for example) for UPS execute command. My UPS stupid > after 'C' and not accept immediately next command on 'upsdrv_initinfo' > procedure. > I strongly recommend to add its. > ________________________________________________ > > I think line: > > send_pace = CLAMP(atoi(getval("sendpace")), 1, 1000) * 1000; > need replaced by > send_pace = CLAMP(atoi(getval("sendpace")), 0, 1000) * 1000; > > Why limiting minimal value to 1 millisecond ? I recommend to allow set > 'send_pace' to ZERO if set ' sendpace=0' in config file 'ups.conf'. > > For Example i test NUT in guest OS in virtual mashine with attached > COM-port, and only after i set 'send_pace' to ZERO in driver source code, > driver start working with my UPS. With ZERO 'send_pace' it work fine. > ________________________________________________ > > And at the end - part of my config (ups.conf), needed for correct working > and displayed data with my UPS. > > [sinapse] > driver = megatec > port = /dev/ttyu0 > desc = "Sinapse 6000" > sendpace=10 # or less, but not more 10 > battvoltmult=108 # for same as on LCD-display on UPS device > battvolts=1.90:2.2400 > _____________________________________________________ > > RESULTS: > > proxy# ./megatec -DDD -a sinapse > Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) > debug level is '3' > DTR=1, RTS=0 > Default command send pace is 100000 usec. > Parameter [sendpace]: [0] > Command send pace changed to 10000 usec. > Starting UPS detection process... > Asking for UPS information [I]... > I => OK [#Sinapse MS II MS3006AG ] > I VALUES => [Sinapse MS II MS3006AG] > Asking for UPS status [Q1]... > Q1 => OK [(212.0 190.0 230.9 018 49.9 2.24 37.0 00000001] > Q1 VALUES => [212.0 190.0 230.9 18.0 49.9 2.2 37.0 00000001] > Asking for UPS status [Q1]... > Q1 => OK [(212.0 190.0 230.9 018 49.9 2.24 37.0 00000001] > Q1 VALUES => [212.0 190.0 230.9 18.0 49.9 2.2 37.0 00000001] > Asking for UPS status [Q1]... > Q1 => OK [(212.0 190.0 230.8 018 49.9 2.24 37.0 00000001] > Q1 VALUES => [212.0 190.0 230.8 18.0 49.9 2.2 37.0 00000001] > Asking for UPS status [Q1]... > Q1 => OK [(212.1 190.0 230.9 018 49.9 2.24 37.0 00000001] > Q1 VALUES => [212.1 190.0 230.9 18.0 49.9 2.2 37.0 00000001] > Asking for UPS status [Q1]... > Q1 => OK [(212.1 190.0 230.9 018 49.9 2.24 37.0 00000001] > Q1 VALUES => [212.1 190.0 230.9 18.0 49.9 2.2 37.0 00000001] > 0 out of 5 detection attempts failed (minimum failures: 2). > Cancelling any pending shutdown or battery test. > Asking for UPS information [I]... > I => OK [#Sinapse MS II MS3006AG ] > I VALUES => [Sinapse MS II MS3006AG] > Megatec protocol UPS detected [Sinapse MS II MS3006AG]. > Parameter [ignoreoff]: [false] > Asking for UPS power ratings [F]... > F => OK [#230.0 026 240.0 50.0] > F VALUES => [230.0 26.0 240.0 50.0] > Unsupported battery voltage (240.0V). > This UPS has an unsupported combination of battery voltage/number of > batteries. > Parameter [battvoltmult]: [108] > The battery voltage reported by the UPS will be multiplied by 108.0. > Parameter [battvolts]: [1.90:2.2400] > Overriding battery voltage interval [1.9V, 2.2V]. > Done setting up the UPS. > Asking for UPS status [Q1]... > Q1 => OK [(211.7 190.0 230.8 019 49.9 2.24 37.0 00000001] > Q1 VALUES => [211.7 190.0 230.8 19.0 49.9 2.2 37.0 00000001] > Calculated battery charge: 100.0% > _________________________________________________ > > > SORRY for my English. > I wanted to write this letter :) > And answer me if my letter useful. once more, try blazer with NUT 2.4.3, and tell us back how it works. cheers, Arnaud _______________________________________________ Nut-upsuser mailing list [email protected] http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser
