Thanks for writing this up, Eran. I believe that this is a step in the right
direction.
Wearing my Bearer Token spec editor hat, I just tried to go through the
exercise of editing my document to use the registry in draft 15 to register the
errors defined in the bearer token spec and I hit a roadblock. Specifically,
while the errors defined by my spec are returned by resource servers (flow F in
Figure 1), the registry defined by draft 15 does not include "resource server
error response" in the "error usage location" list. Can you please add this
additional error usage location so that the registry can be used by the bearer
token specification?
At that point, I believe we'll be able to close the open issue about the need
for an error registry, and I'll update my draft accordingly.
Thank you,
-- Mike
From: [email protected] [mailto:[email protected]] On Behalf Of Eran
Hammer-Lahav
Sent: Tuesday, April 05, 2011 3:52 PM
To: OAuth WG
Subject: [OAUTH-WG] Error registry proposal (round 3)
The following is my new proposal, based on Mike Jones' and my earlier
proposals. It is basically a combination of the two.
This proposal does not allow defining new error codes unless another extension
is involved (new grant type, request parameter, token type). The reason for not
defining an open ended error registry is that defining new error codes for
existing implementations is bad for interoperability and can lead to unexpected
results (developers not taking into account receiving a new error when talking
to a compliant 2.0 server). We don't have any use cases for defining such new
errors for the v2 specification. New errors only come from extensions and must
be defined in that context.
I have applied to changes to the -14 draft and clearly marked them with
[[Pending Consensus]] so that there is no issue with removing them or changing
them later.
---
Add to the error codes list in sections 4.1.2.1 and 4.2.2.1:
a 4xx or 5xx HTTP status code (except for 400 and 401)
The authorization server MAY set the "error" parameter
value to a numerical HTTP status code from the 4xx or 5xx
range, with the exception of the 400 (Bad Request) and
401 (Unauthorized) status codes. For example, if the
service is temporarily unavailable, the authorization
server MAY return an error response with "error" set to
"503".
Add a new section 8.4:
8.4. Defining Additional Error Codes
In cases where protocol extensions (i.e. access token types,
extension parameters, or extension grant types) require additional
error codes to be used with the authorization code grant error
response (Section 4.1.2.1), the implicit grant error response
(Section 4.2.2.1), or the token error response (Section 5.2), such
error codes MAY be defined.
Extension error codes MUST be registered (following the procedures in
Section 10.3) if the extension they are used in conjunction with is
registered. Additional error codes used with unregistered extensions
MAY be registered.
Error codes MUST conform to the error-code ABNF, and SHOULD be
prefixed by an identifying name when possible. For example, an error
identifying an invalid value set to the extension parameter "example"
should be named "example_invalid".
error-code = ALPHA *error-char
error-char = "-" / "." / "_" / DIGIT / ALPHA
Add a new section 10.3:
10.3. The OAuth Extensions Error Registry
This specification establishes the OAuth extensions error registry.
Additional error codes used together with other protocol extensions
(i.e. extension grant types, access token types, or extension
parameters) are registered on the advice of one or more Designated
Experts (appointed by the IESG or their delegate), with a
Specification Required (using terminology from [RFC5226]). However,
to allow for the allocation of values prior to publication, the
Designated Expert(s) may approve registration once they are satisfied
that such a specification will be published.
Registration requests should be sent to the [TBD]@ietf.org mailing
list for review and comment, with an appropriate subject (e.g.,
"Request for error code: example"). [[ Note to RFC-EDITOR: The name
of the mailing list should be determined in consultation with the
IESG and IANA. Suggested name: oauth-ext-review. ]]
Within at most 14 days of the request, the Designated Expert(s) will
either approve or deny the registration request, communicating this
decision to the review list and IANA. Denials should include an
explanation and, if applicable, suggestions as to how to make the
request successful.
Decisions (or lack thereof) made by the Designated Expert can be
first appealed to Application Area Directors (contactable using
[email protected]<mailto:[email protected]> email address or
directly by looking up their
email addresses on http://www.iesg.org/ website) and, if the
appellant is not satisfied with the response, to the full IESG (using
the [email protected]<mailto:[email protected]> mailing list).
IANA should only accept registry updates from the Designated
Expert(s), and should direct all requests for registration to the
review mailing list.
10.3.1. Registration Template
Error name:
The name requested (e.g., "example").
Error usage location:
The location(s) where the error can be used. The possible
locations are: authorization code grant error response
(Section 4.1.2.1), implicit grant error response
(Section 4.2.2.1), or token error response (Section 5.2).
Related protocol extension:
The name of the extension grant type, access token type, or
extension parameter, the error code is used in conjunction with.
Change controller:
For standards-track RFCs, state "IETF". For others, give the name
of the responsible party. Other details (e.g., postal address,
e-mail address, home page URI) may also be included.
Specification document(s):
Reference to document that specifies the error code, preferably
including a URI that can be used to retrieve a copy of the
document. An indication of the relevant sections may also be
included, but is not required.
_______________________________________________
OAuth mailing list
[email protected]
https://www.ietf.org/mailman/listinfo/oauth
