On 03/10/2017 05:42 PM, Denis Kenzior wrote: > Hi Christophe, > > On 03/10/2017 10:13 AM, Christophe Ronco wrote: >> Hi, >> >> I am using a LE910-EU V2 modem (from Telit). I have a SIM card with PIN >> code activated. >> >> With this setup, I never have CardIdentifier property in >> org.ofono.SimManager properties. This is because Ofono fails to read >> ICCID. >> >> >> In traces, I see all commands AT+CRSM sent during init (before PIN is >> entered) failing. For example: >> >> Aux: > AT+CRSM=192,28590\r >> Aux: < \r\n+CME ERROR: 4\r\n >> >> >> I assume this is an intended behavior from Telit as described in their >> AT reference guide (page 124): >> >> https://www.coniugo.de/tl_files/dateien/downloads/at/AT%20Commands%20LE910.pdf >> >> >> >> The note says: >> >> this command requires PIN authentication. However commands READ BINARY >> and READ RECORD can be issued before PIN authentication and if the SIM >> is blocked (after three failed PIN authentication attempts) to access >> the contents of the Elementary Files. >> >> 192 is GET RESPONSE, READ BINARY is 176 and READ RECORD is 178 >> > > The SIM filesystem guarantees that certain files are always readable. > From memory this includes EFiccid, EFpl, EFecc and a few others. Since > some of these are record based files of variable length (for example > EFecc) we need to look up the record length first. > > Otherwise, as an example, we can't read SIM specific emergency calling > codes when the SIM PIN hasn't been entered. Being able to do so is > mandated by 3GPP. From memory, EFdir and EFarr should always be > accessible as well (see ETSI 102.221), so this just seems like a stupid > limitation. > >> >> I tried to manage the modem without Ofono to verify that. Here is what I >> tried: >> >> AT+CPIN? >> +CPIN: SIM PIN >> >> OK >> AT+CRSM=192,12258 >> ERROR >> AT+CRSM=176,12258,0,0,255 >> +CRSM: 103,0 >> >> OK >> AT+CRSM=176,12258,0,0,10 >> +CRSM: 144,0,98331002040320818103 >> >> OK >> AT+CPIN=0000 >> OK >> AT+CRSM=192,12258 >> +CRSM: 144,0,62178202412183022FE28A01058B032F06098002000A880110 >> >> OK >> >> >> So I am able to read ICCID before entering PIN code but to do that, I >> need to use AT+CRSM=176,12258,.... and not AT+CRSM=192,12258 as it is >> done by Ofono. >> >> I had a look at code in src/sim.c and src/simfs.c and it seems that any >> read command will first call at driver level read_file_info and then >> read_file_transparent. >> >> I don't know how to fix that in Ofono code (if it should be fixed). >> Should I call directly read_file_transparent in sim_initialize (instead >> of ofono_sim_read) to get ICCID ? Should I modify ofono_sim_read to use >> read_file_transparent directly (in some cases at least)? >> > > EFiccid is special in that it is always 10 bytes, so you could cheat and > read it directly via read_file_transparent. Similar to how it is done > for EFimsi. However, I don't think this would work for other files, > e.g. EFecc, etc. > > Regards, > -Denis > _______________________________________________ > ofono mailing list > [email protected] > https://lists.ofono.org/mailman/listinfo/ofono Hi, i did notice this problem as well (on FW 20.00.402) and notified Telit support. They said they are aware of this issue and provided me with test firmware that is supposed to correct this. I have not tried it yet due to a lack of time.
Piotr _______________________________________________ ofono mailing list [email protected] https://lists.ofono.org/mailman/listinfo/ofono
