xinetd is running and the following is
my /opt/omd/sites/SlaveRPLS/etc/mk-livestatus/xinetd.conf
service livestatus
{
type = UNLISTED
socket_type = stream
protocol = tcp
wait = no
# limit to 100 connections per second. Disable 3 secs if above.
cps = 100 3
# set the number of maximum allowed parallel instances of unixcat.
# Please make sure that this values is at least as high as
# the number of threads defined with num_client_threads in
# etc/mk-livestatus/nagios.cfg
instances = 500
# limit the maximum number of simultaneous connections from
# one source IP address
per_source = 250
# Disable TCP delay, makes connection more responsive
flags = NODELAY
# configure the IP address(es) of your Nagios server here:
# only_from = 127.0.0.1 10.0.20.1 10.0.20.2
# ----------------------------------------------------------
# These parameters are handled and affected by OMD
# Do not change anything beyond this point.
# Disabling is done via omd config set LIVESTATUS_TCP [on/off].
# Do not change this:
disable = no
# TCP port number. Can be configure via LIVESTATUS_TCP_PORT
port = 6557
# Paths and users. Manual changes here will break some omd
# commands such as 'cp', 'mv' and 'update'. Do not toutch!
user = SlaveRPLS
server = /omd/sites/SlaveRPLS/bin/unixcat
server_args = /omd/sites/SlaveRPLS/tmp/run/live
# ----------------------------------------------------------
}
There is no port listed so should I add?
Thanks.
On 7 May 2015 at 14:48, May,Allen <[email protected]> wrote:
> Is your livestatus set and xinetd restarted? Disable = yes may be the
> default…can’t remember.
>
>
>
>
>
> # cat /etc/xinetd.d/livestatus
>
> service livestatus
>
> {
>
> type = UNLISTED
>
> port = 6557
>
> socket_type = stream
>
> protocol = tcp
>
> wait = no
>
> # limit to 100 connections per second. Disable 3 secs if above.
>
> cps = 100 3
>
> # set the number of maximum allowed parallel instances of unixcat.
>
> # Please make sure that this values is at least as high as
>
> # the number of threads defined with num_client_threads in
>
> # etc/mk-livestatus/nagios.cfg
>
> instances = 500
>
> # limit the maximum number of simultaneous connections from
>
> # one source IP address
>
> per_source = 250
>
> # Disable TCP delay, makes connection more responsive
>
> flags = NODELAY
>
> user = lab
>
> server = /omd/sites/lab/bin/unixcat
>
> server_args = /omd/sites/lab/tmp/run/live
>
> # configure the IP address(es) of your Nagios server here:
>
> # only_from = 127.0.0.1 10.0.20.1 10.0.20.2
>
> disable = no
>
> }
>
> *From:* [email protected] [mailto:
> [email protected]] *On Behalf Of *Peter Shankland
> *Sent:* Thursday, May 07, 2015 8:42 AM
> *To:* [email protected]
> *Subject:* [omd-users] Fresh Install of OMD 1.20 on CentOS 6.6 64Bit -
> Livestatus Not Running
>
>
>
> Hi all,
>
>
>
> As the subject suggests, I have created two new CentOS 6.6 64Bit servers
> and installed OMD 1.20 on them ready to use one as a master and the other
> as a slave. The installations appear to have gone fine and I have managed
> to configure the distributed monitoring and the config has gone from the
> master to the slave.
>
>
>
> The issue I have is with Livestatus as nothing is getting reported back to
> the master. Also, when I run netstat -ln|grep 6557 on both machines,
> nothing is reporting.
>
>
>
> My nagios.log shows the following:
>
>
>
> [1431005132] livestatus: Finished initialization. Further log messages go
> to /omd/sites/SlaveRPLS/var/nagios/livestatus.log
>
> [1431005132] Event broker module
> '/omd/sites/SlaveRPLS/lib/mk-livestatus/livestatus.o' initialized
> successfully.
>
> [1431005132] Finished daemonizing... (New PID=1444)
>
> [1431005132] TIMEPERIOD TRANSITION: 24X7;-1;1
>
> [1431005132] TIMEPERIOD TRANSITION: 24x7;-1;1
>
> [1431005132] TIMEPERIOD TRANSITION: none;-1;0
>
> [1431005132] TIMEPERIOD TRANSITION: thruk_24x7;-1;1
>
> [1431005132] logging initial states
>
>
>
> and my livestatus.log shows this:
>
>
>
> 2015-05-07 14:25:15 deinitializing
>
> 2015-05-07 14:25:15 Waiting for main to terminate...
>
> 2015-05-07 14:25:17 Waiting for client threads to terminate...
>
> 2015-05-07 14:25:17 Logfile cache: flushing complete cache.
>
>
>
> The above is happening on both machines.
>
>
>
> So, I can see that livestatus is not running but not sure how to start
> debugging the issue from here as first time using it and OMD - any
> suggestions would be useful.
>
>
>
> Thanks.
>
> ------------------------------
> ---------------------------------------------------------------------------
> The information transmitted in this e-mail and in any replies and forwards
> are for the sole use of the above individual(s) or entities and may contain
> proprietary, privileged and/or highly confidential information. Any
> unauthorized dissemination, review, distribution or copying of these
> communications is strictly prohibited. If this e-mail has been transmitted
> to you in error, please notify and return the original message to the
> sender immediately at the above listed address. Thank you for your
> cooperation.
>
>
_______________________________________________
omd-users mailing list
[email protected]
http://lists.mathias-kettner.de/mailman/listinfo/omd-users
