Lusheng,How do you use the cli tool within AT&T? I want to set up a simple web server to host the templates and blueprints. The reason why I ask this is that we want to verify the component specification files on our own. As you know, they are not completely done. Otherwise, we have to send those files to your team for verification every time we make any tiny changes. I think that might be quite annoying and less efficient.Any advice on this will be helpful and welcome. Thanks. Guangrong 原始邮件
发件人:JI,LUSHENG(LUSHENG) 收件人:付光荣10144542; 抄送人:[email protected];彭聪聪6128000043;HWANG, MICHAEL(MICHAEL); 日期:2017-10-09 20:32:58 主题:Re: 答复：[dcae] dcae-cli Installation Failure Guangrong, I discussed with Michael about this subject. Using ONAP Nexus is not an ideal solution. The reason is that from DCAE cli perspective, Nexus is read only (write access is only from Gerrit). Therefore any new schema onboarded from cli cannot be added to Nexus from DCAE cli. I donot have a good solution. Maybe we will have to launch a VM in Pod25. But VMs there are often rebuilt so they are not very "stable". So special care needs to be taken for resiliency. The same problem existing for all ONAP design time flows and components. I donot know for example how SDC stores its blueprints and catalog.. If they have a solution we can probably use the same solution. Lusheng Sent via the Samsung Galaxy S7, an AT&T 4G LTE smartphone -------- Original message -------- From: [email protected] Date: 10/9/17 6:27 AM (GMT-05:00) To: "JI, LUSHENG (LUSHENG)" <[email protected]> Cc: [email protected], [email protected], "HWANG, MICHAEL (MICHAEL)" <[email protected]> Subject: Re: 答复：[dcae] dcae-cli Installation Failure Lusheng, Do you have any suggestion on this? If the ONAP nexus server could not be used, could you please give us some guidance on setting up such a server (such as the dir hirarchy on the server side and the dir names, etc.)? Thanks. Guangrong Sender: <[email protected]>; To: fuguangrong10144542; CC: <[email protected]>; <[email protected]>;pengcongcong6128000043; Date: 2017/10/05 02:51 Subject: Re: 答复：[dcae] dcae-cli Installation Failure The dcae-cli expects json schema files and the server is a simple web server that hosts these files. @Lusheng could we use ONAP's nexus raw file server to serve up these files? On 10/04/2017 01:27 AM, [email protected] wrote: Mike, We succeeded in installing the dcae-cli tool. But when I try to initialize it using dcae_cli --reinit or to check the version using dcae_cli --version, the url of a server is required: What is the url of the remote server, please? Do we have to set up such a server by ourselves? Thanks. Guangrong Sender: <[email protected]>; To: fuguangrong10144542; CC: <[email protected]>; <[email protected]>;pengcongcong6128000043; Date: 2017/09/27 22:23 Subject: Re: 答复：[dcae] dcae-cli Installation Failure I just tried in a new virtualenv and the cli installed for me ok. On 09/27/2017 10:03 AM, [email protected] wrote: Thank you, Mike. We've already had a postgres running locally. We'll try to install the cli tool from the source using the pip instruction you provided tomorrow. (I have limited access to our internal lab while I'm in Paris so I'll leave that to my team. :D) @Peng Could you please try it again following the suggestion below? If there's still problem, pls let us know asap. Thanks.. Guangrong Sender: <[email protected]>; To: fuguangrong10144542; CC: <[email protected]>; <[email protected]>;pengcongcong6128000043; Date: 2017/09/27 21:57 Subject: Re: 答复：[dcae] dcae-cli Installation Failure Hi Guangrong Rather than checking out source and trying to install from source, can you do a: pip install onap-dcae-cli instead? Note: The onboarding env is not completely setup so your dcae-cli will work in a limited capacity. As a requirement, you will need a local postgres server running. A fast way to get postgres running is to run a docker instance. See the README in the dcae-cli project for more details on "Local use". Thanks Mike On 09/27/2017 04:46 AM, [email protected] wrote: Hi Mike, I'm sending this again in case the screenshots in Lusheng's previous email can not be displayed properly. (It did happen on my laptop.) Thanks. Guangrong Sender: fuguangrong10144542 To: <[email protected]>; CC: <[email protected]>;pengcongcong6128000043; Date: 2017/09/27 04:23 Subject: 答复：[dcae] dcae-cli Installation Failure Lusheng, It was really great time talking with you in a F2F manner this evening. I hope will get more chances to have such kind of conversations in the future. As I mentioned, there are still problems when we try to install the dcae-cli tool based on the latest codes in the gerrit repo. Could you please help to reach out to your team for confirmation? I know that they are struggling with the sonar things. We'll appreciate their help if they could spare some time to take a look at it. Thanks. Guangrong Sender: 付光荣10144542 To: [email protected]; CC: [email protected];彭聪聪6128000043; Date: 2017-09-25 21:23:33 Subject: [dcae] dcae-cli Installation Failure Sender: fuguangrong10144542 To: <[email protected]>; CC: peng//cong/cong6128000043; Date: 2017/09/25 21:21 Subject: [dcae] dcae-cli Installation Failure Hi Lusheng, It seems that your team has updated the dcae-cli codes a little bit. But when we try to install the tool, there are still errors (see the screenshot below). Are there any configurations missing on our side? It looks like the external repo address is missing. Could you please help to solve that? Thanks. Guangrong Sender: peng//cong/cong6128000043 To: fuguangrong10144542; Date: 2017/09/25 20:52 Subject: 【dcae-cli】Python setup.py install 失败 错误信息：
_______________________________________________ onap-discuss mailing list [email protected] https://lists.onap.org/mailman/listinfo/onap-discuss
