Turns out I don't have the VMWare image put in place yet (recently re-did my computer and lost it). Until I get the image downloaded again, I would suggest checking the Apache logs. Depending on how it was actually installed, it may be /var/log/apache2/error_log or something else.
--Don On 7/31/07, John van Rassel <[EMAIL PROTECTED]> wrote: > Ok...I looked at the /etc/apache2/httpd.conf file, and found this: > <Directory "/var/www/localhost/cgi-bin/"> > AllowOverride None > Options None > Order allow,deny > Allow from all > </Directory> > > This seems to me like it would allowing from all IP's. I don't really > know what to do. I might be looking at the wrong place, or something > else, so I am open to ideas > Thanks > John > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of > Don McMorris > Sent: Tuesday, July 31, 2007 3:15 PM > To: [email protected] > Subject: Re: [OPEN-ILS-GENERAL] Setting up Branches > > Hi John: > > The installation calls to lock the /cgi-bin/ folder to prevent a > malicious user from re-bootstrapping the system. To modify or remove > this lock, you will need to edit the apache configuration. I don't > have the image here in front of me, but I believe it's in the actual > apache configuration which is probably located in > /etc/httpd/apache2/conf/ (or similar). I forget exactly how the > VMWare image is configured (and it's not here where I am), so if you > get stuck I'll take a look when I get home (or Dan will come to the > rescue again ;)). > > What you'd be looking for is something in one of the Apache configs > along the line of: > <Directory /cgi-bin> > ... > Order deny,allow > deny from all > allow from [space-delimited list of IP addresses]. > </Directory> > > This is all from memory, so it may not be exact.. but hopefully it'll > get you started. > > Good luck! > > --Don > > > On 7/31/07, John van Rassel <[EMAIL PROTECTED]> wrote: > > I tried this, but now I get a 403 error. It says You don't have > > permission to access /cgi-bin/config.cgi on this server. > > Does anyone know what I may be doing wrong? > > Thanks > > John > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] On Behalf > Of > > Dan Scott > > Sent: Monday, July 30, 2007 11:00 AM > > To: [email protected] > > Subject: Re: [OPEN-ILS-GENERAL] Setting up Branches > > > > On 30/07/07, John van Rassel <[EMAIL PROTECTED]> wrote: > > > > > > Is there any sort of utility for setting up different branches in > > Evergreen? > > > > There sure is - in fact, there are two. > > > > > Right now, I am using the Gentoo image(thanks to Dan), but now I > want > > to get > > > rid of the sample branches, and put our own in > > > > Try opening http://192.168.1.128/cgi-bin/config.cgi in a Web browser > > (replacing 192.168.1.128 with whatever IP address your VMWare image > > acquired); you'll be able to drill down through the org_unit hierarchy > > and change names, etc, at will. > > > > > I was just hoping someone could let me know the best way to do this > > > > There will be an even better way soon; a complete administration > > interface built on Django is in the works. In fact, the base code for > > it is in the VMWare image; I just haven't enabled it yet. I hope to > > have it running for the 1.2.0-final image, even if it's still under > > development, because it looks so darn cool. > > > > -- > > Dan Scott > > Laurentian University > > >
