Hello, I have a TI Omap3503 EVM board and I am trying to get OE up and working on it. I am using the angstrom 2008.1 distro with the beagleboard as machine. The beagleboard uses the same omap processor (omap3530). And it appears as though oe is working for the beagleboard.
Here is my configuration file ====================================================================== BFILES = "/home/projects/oe/stuff/org.openembedded.dev/packages/*/*.bb" DISTRO = "angstrom-2008.1" MACHINE = "beagleboard" IMAGE_FSTYPES="tar.bz2" ====================================================================== I can run bitbake task-base and it appears to build correctly. ====================================================================== NOTE: Tasks Summary: Attempted 1467 tasks of which 0 didn't need to be rerun and 0 failed. NOTE: build 200806041351: completed ====================================================================== However when I try to run the kernel (via tftp, or from flash) it does the following. ====================================================================== OMAP3EVM # run bootcmd Reseting CHIP... Done LAN9x18 (0x01150002) detected. start Auto negotiation... (take ~2sec) Auto negotiation complete, 100BaseTX, full duplex Hit any key to stop autoboot: 0 OMAP3EVM # setenv get_kernel run tftp_kernel OMAP3EVM # run bootcmd Reseting CHIP... Done LAN9x18 (0x01150002) detected. start Auto negotiation... (take ~2sec) Auto negotiation complete, 100BaseTX, full duplex TFTP from server 192.168.20.176; our IP address is 192.168.20.201 Filename 'uImage'. Load address: 0x80000000 Loading: ################################################################# ... ################################################################# done Bytes transferred = 2155668 (20e494 hex) ## Booting image at 80000000 ... Image Name: Angstrom/2.6.25+2.6.26-rc4+git24 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2155604 Bytes = 2.1 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... ====================================================================== Then it appears to lock up. Normally, when using the kernel that came with TI's SDK, the output is the following. ====================================================================== LAN9x18 (0x01150002) detected. start Auto negotiation... (take ~2sec) Auto negotiation complete, 100BaseTX, full duplex TFTP from server 192.168.20.176; our IP address is 192.168.20.201 Filename 'uImage'. Load address: 0x80000000 Loading: ################################################################# ... ################################################################# done Bytes transferred = 1821644 (1bcbcc hex) ## Booting image at 80000000 ... Image Name: Linux-2.6.22.1-omap3 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1821580 Bytes = 1.7 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................... done, booting the kernel. Linux version 2.6.22.1-omap3 ([EMAIL PROTECTED]) (gcc version 4.2.3 (Sourcery G++ Lite 2008q1-126)) #1 Wed May 28 16:58:48 PDT 2008 CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=00c5387f . . . ====================================================================== Does anyone have any ideas as to what I am doing wrong. It looks like uboot recognizes the uImage file and the uboot info displays for the two kernel match between the TI supplied kernel and the OE built kernel in all but the Image name. I realize this question might be better directed to beagleboard developers but thought I would try here first. Thanks, Ben Anderson _______________________________________________ Openembedded-users mailing list [email protected] http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-users
