Hi Ian, I've just installed my wr1043nd v1.10 using attitude adjustment. So far, works good. :)
On Fri, Feb 15, 2013 at 4:39 AM, Ian Ku <ia...@cs.ucla.edu> wrote: > Using this thread, > > did anyone successfully tried openflow-openwrt on TP-LINK TL-WR1043ND > v1.10? > the openwrt site seems to imply that using the v1.7 or v1.8 will brick the > router (since those umages are using Backfire 10.03.1) > > thanks! > > > > On Thu, Feb 7, 2013 at 12:51 AM, Shabbir Ahmed <shabbir1...@gmail.com>wrote: > >> why dont u try sysupgrade on openwrt? make new image and upgrade from >> cli. >> >> im glade to see a person whos already running openflow on this tp-link >> caz i just ported openflow onto it and im having trouble. can u guide me or >> share the topology configuration and controller information? >> >> ill be thank full :D >> >> thank you, >> Shabbir. >> >> >> On Thu, Feb 7, 2013 at 8:48 AM, Humphrey Lee <iramani...@gmail.com>wrote: >> >>> Hi Yiannis, >>> >>> I have v1.7 Pantou image on my TL-1043ND AP now. I want to upgrade it to >>> v1.8 image. I understand I need to use tftp to do so. Is there a document >>> or an article to describe the steps? >>> >>> By the way, how did you implement DHCP on your OpenFlow-enabled TP-LINK >>> AP? Did you do it on the OpenFlow Controller? Is there a DHCP module for >>> FloodLight for testing? >>> >>> I appreciate your support. >>> >>> Cheers, >>> Humphrey >>> >>> On Thu, Jan 24, 2013 at 11:51 AM, Yiannis Yiakoumis < >>> yiann...@stanford.edu> wrote: >>> >>>> Did you use the right binary for your AP version (1.7, 1.8 etc)? >>>> Also, note that you should try to reach the AP at 192.168.1.1 through >>>> the WAN/Internet port, not the local ports.. >>>> >>>> If none of this works, try tftp to download another image, e.g. a >>>> standard openwrt or the TP-Link original firmware. >>>> >>>> Regards, >>>> Yiannis >>>> >>>> >>>> On Wed, Jan 23, 2013 at 7:36 PM, Humphrey Lee <iramani...@gmail.com>wrote: >>>> >>>>> Hello, >>>>> >>>>> I just bought a TP-LINK TL-WR1043ND AP. After I flashed its firmware >>>>> with the downloaded Pantou image "ofwrt-tplink-factory.bin", then I was >>>>> not >>>>> able to connect(ping, telnet) 192.168.1.1 anymore. I might have flashed >>>>> the >>>>> incorrect Pantou image. How can I rescue it? >>>>> >>>>> I appreciate any suggestion or comment. >>>>> >>>>> Cheers, >>>>> Humphrey >>>>> >>>>> _______________________________________________ >>>>> openflow-discuss mailing list >>>>> openflow-discuss@lists.stanford.edu >>>>> https://mailman.stanford.edu/mailman/listinfo/openflow-discuss >>>>> >>>>> >>>> >>> >>> _______________________________________________ >>> openflow-discuss mailing list >>> openflow-discuss@lists.stanford.edu >>> https://mailman.stanford.edu/mailman/listinfo/openflow-discuss >>> >>> >> >> _______________________________________________ >> openflow-discuss mailing list >> openflow-discuss@lists.stanford.edu >> https://mailman.stanford.edu/mailman/listinfo/openflow-discuss >> >> > > _______________________________________________ > openflow-discuss mailing list > openflow-discuss@lists.stanford.edu > https://mailman.stanford.edu/mailman/listinfo/openflow-discuss > > -- Regards, Agung Ridwan SN Telecommunication Engineering School of Electrical Engineering and Informatics
_______________________________________________ openflow-discuss mailing list openflow-discuss@lists.stanford.edu https://mailman.stanford.edu/mailman/listinfo/openflow-discuss
