Hi, The way you are creating the queues is right. You can check the queues you are making by a command of ovsctl (don't really remember it now). However i am not sure about the slices you are making since I haven't worked with flow visor.
Why are you running two controllers? On Tuesday, 9 February 2016, Guillermo Chica Sabariego < guillermoch...@correo.ugr.es> wrote: > Hello everyone, > > I am running a small experiment to isolate bandwidth with flowvisor > (version 1.4) implementing a port based slicing. With mininet, I create a > topology that consists of a host h1 (10.0.0.1), connected to a switch, > called s3, connected to another host, h2 (10.0.0.2), this way: > > h1 ----- s3 ------ h2 > > > To achieve this I use this mininet command: sudo mn --custom simpletopo.py > --topo mytopo --switch ovsk --controller remote --mac --arp --link tc > > I want all traffic going to port 666 from h1 to h2 to have a bandwidth of > 1Mbps, and all traffic going to port 555 from h1 to h2 to have a bandwidth > of 1Gbps. To achieve this, I create two queues in switch s3, q0 and q1. q0 > is for the 1Mbps traffic and q1 for 1Gbps traffic. > > I create the queues like this: > > sudo ovs-vsctl -- set Port s3-eth1 qos=@newqos -- --id=@newqos create QoS > type=linux-htb other-config:max-rate=10000000000 queues=0=@q0,1=@q1 -- > --id=@q0 create Queue other-config:min-rate=1000000 > other-config:max-rate=1000000 -- --id=@q1 create Queue > other-config:min-rate=1000000000 other-config:max-rate=1000000000 > > sudo ovs-vsctl -- set Port s3-eth2 qos=@newqos -- --id=@newqos create QoS > type=linux-htb other-config:max-rate=10000000000 queues=0=@q0,1=@q1 -- > --id=@q0 create Queue other-config:min-rate=1000000 > other-config:max-rate=1000000 -- --id=@q1 create Queue > other-config:min-rate=1000000000 other-config:max-rate=1000000000 > > I have supposed that it's necessary to create a QoS for the two interfaces > that connect the switch to the hosts, that is a QoS for eth1 and a QoS for > eth2. But I'm not sure of this. Can anyone tell me if I'm wrong? > > Then, I have created the two slices. Slice1 for traffic going to and from > port 666 and slice2 for traffic going to and from port 555. > > fvctl add-slice slice1 tcp:127.0.0.2:6643 gene...@email.com > fvctl add-slice slice2 tcp:127.0.0.3:6653 gene...@email.com > > fvctl add-flowspace --forced-queue=1 flow1 3 100 > in_port=1,nw_src=10.0.0.1,nw_dst=10.0.0.2,tp_dst=666 slice1=7 > fvctl add-flowspace --forced-queue=0 flow2 3 100 > in_port=1,nw_src=10.0.0.1,nw_dst=10.0.0.2,tp_dst=555 slice2=7 > fvctl add-flowspace --forced-queue=1 flow3 3 100 > in_port=2,nw_src=10.0.0.2,nw_dst=10.0.0.1,tp_src=666 slice1=7 > fvctl add-flowspace --forced-queue=0 flow4 3 100 > in_port=2,nw_src=10.0.0.2,nw_dst=10.0.0.1,tp_src=555 slice2=7 > > After this, I run the controllers of each slice: > > ./pox.py --verbose pox.openflow.of_01 --address=127.0.0.2 --port=6643 > pox.forwarding.l2_learning > ./pox.py --verbose pox.openflow.of_01 --address=127.0.0.3 --port=6653 > pox.forwarding.l2_learning > > Then, I run the topology in mininet, with the command given above. And > finally, I run a test with iperf to test the bandwidth. However, I always > get a bandwidth of 17-18 Gbps. So flowvisor force-enqueue option is not > working. What is wrong with my procedure? Maybe a problem with the queues I > have created? I'd appreciate any help. > > Thank you. > > Best regards, > Guillermo Chica. > _______________________________________________ > openflow-discuss mailing list > openflow-discuss@lists.stanford.edu > https://mailman.stanford.edu/mailman/listinfo/openflow-discuss >
_______________________________________________ openflow-discuss mailing list openflow-discuss@lists.stanford.edu https://mailman.stanford.edu/mailman/listinfo/openflow-discuss
