Hi again Chris, On Fri, 2006-04-14 at 10:39, Chris Worley wrote: > Hal, > > You're correct... the results of the scans are in /var/log/osm.log. I > was expecting the "-console" mode to show more. > > In looking at the /var/log/osm.log I'm seeing a lot of: > > Reporting Generic Notice type:4 num:144 > > For different GUIDs.
What's a lot ? One for each GUID ? What's the capability mask indicated ? > Is there a place to look these up? Yes, the IBA spec (volume 1). Trap 144 indicates that the capability mask at the indicated LID has changed. > I still don't have IPoIB running, and ibv_devinfo says I'm not setup > right either (couldn't open a device). I'm not sure why not. -- Hal > Thanks, > > Chris > On 14 Apr 2006 10:22:22 -0400, Hal Rosenstock <[EMAIL PROTECTED]> wrote: > > Hi Chris, > > > > On Fri, 2006-04-14 at 10:19, Chris Worley wrote: > > > I installed the SuSE 10 OpenIB RC2 RPMS. > > > > > > The installation went well, but I'm stuck at the startup. > > > > > > As an IBGD user, I'm used to an init file in /etc/init.d... but there was > > > none. > > > > > > >From the wiki, I was able to glean: > > > > > > Make the udev file: > > > > > > # cat > /etc/udev/rules.d/40-infiniband.rules > > > KERNEL="umad*", NAME="infiniband/%k" > > > KERNEL="issm*", NAME="infiniband/%k" > > > > > > Install some modules: > > > > > > modprobe ib_ucm > > > modprobe ib_cm > > > modprobe ib_uverbs > > > modprobe ib_umad > > > > > > And make sure udev is running, and start the opensm. > > > > > > I've done this on all nodes, and ibstat shows I have a link up and > > > running on every node. Opensm doesn't show any scanning. It's been > > > hung all night at: > > > > > > # opensm --console > > > ------------------------------------------------- > > > OpenSM Rev:openib-1.2.0 > > > Based on OpenIB svn Exported revision > > > Command Line Arguments: > > > Enabling OpenSM interactive console > > > Log File: /var/log/osm.log > > > ------------------------------------------------- > > > OpenSM Rev:openib-1.2.0 OpenIB svn Exported revision > > > > > > Using default guid 0x2c9020020c3ce > > > > > > OpenSM Console > > > > > > $ Entering MASTER state > > > > > > SUBNET UP > > > > Looks like everything is fine from the OpenSM standpoint. > > > > I see no indication that OpenSM is hung. You are in the console. > > > > Also, why do you say OpenSM isn't "scanning" ? > > > > What is in /var/log/osm.log ? Any errors ? > > > > If you want more verbose messages start OpenSM with -V. > > > > -- Hal > > > > > IPoIB isn't up. ibv_rc_pingpong doesn't work. Neither does ibv_devinfo. > > > > > > Is there a definitive guide on the initialization of the drivers and > > > fabric? > > > > > > Also, is there an MVAPICH2 for SuSE 10 RPM? > > > > > > Thanks, > > > > > > Chris > > > _______________________________________________ > > > openib-general mailing list > > > [email protected] > > > http://openib.org/mailman/listinfo/openib-general > > > > > > To unsubscribe, please visit > > > http://openib.org/mailman/listinfo/openib-general > > > > > _______________________________________________ > openib-general mailing list > [email protected] > http://openib.org/mailman/listinfo/openib-general > > To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general _______________________________________________ openib-general mailing list [email protected] http://openib.org/mailman/listinfo/openib-general To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general
