Quoting r. Ken L Johnson <[EMAIL PROTECTED]>: > Subject: ib_mthca fails to load with old firmware > > I'm running into a problem when I try to use the OFED RC4 release on some > blade systems that have TopSpin HCA daughter cards installed (actually > Mellanox). I'm trying to figure out how to update the firmware to the latest > [ http://mellanox.com/support/firmware_table.php ] but it seems I must know > the PSID so I can grab the right firmware image. Can anyone point me in the > right direction here? > > ---8<--- [query device using flint] > > blade9:~ # flint -d /dev/mst/mt25208_pci_cr0 q > Image type: Failsafe > I.S. Version: 1 > Chip Revision: A0 > GUID Des: Node Port1 Port2 Sys image > GUIDs: 0005ad000002ad1d 0005ad000002ad1e 0005ad000002ad1f > 0005ad000100d050 > Board ID: 1 > VSD: 1 > PSID: > > --->8--- > > ---8<--- [dmesg output showing ib_mthca load failure] > > <6>ib_mthca: Mellanox InfiniBand HCA driver v0.08 (February 14, 2006) > <6>ib_mthca: Initializing 0000:02:00.0 > <6>ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169 > <7>PCI: Setting latency timer of device 0000:02:00.0 to 64 > <6>e1000: eth0: e1000_watchdog_task: NIC Link is Up 1000 Mbps Full Duplex > <4>ib_mthca 0000:02:00.0: HCA FW version 4.6.0 is old (4.7.400 is current). > <4>ib_mthca 0000:02:00.0: If you have problems, try updating your HCA FW. > <3>ib_mthca 0000:02:00.0: NOP command failed to generate interrupt (IRQ > 169), aborting. > <3>ib_mthca 0000:02:00.0: BIOS or ACPI interrupt routing problem? > <6>ACPI: PCI interrupt for device 0000:02:00.0 disabled > <4>ib_mthca: probe of 0000:02:00.0 failed with error -16 > > --->8--- > > > ---8<--- [hwinfo & lspci output for HCA] > > blade9:~ # hwinfo > [...] > 24: PCI 200.0: 0c06 InfiniBand > [Created at pci.277] > Unique ID: B35A.guWNc33i6_3 > Parent ID: 8otl.l6V0RupyGX6 > SysFS ID: /devices/pci0000:00/0000:00:04.0/0000:02:00.0 > SysFS BusID: 0000:02:00.0 > Hardware Class: unknown > Model: "Mellanox MT25208 InfiniHost III Ex HCA (Tavor compatibility mode)" > Vendor: pci 0x15b3 "Mellanox Technologies" > Device: pci 0x6278 "MT25208 InfiniHost III Ex HCA (Tavor compatibility > mode)" > SubVendor: pci 0x15b3 "Mellanox Technologies" > SubDevice: pci 0x6278 > Revision: 0xa0 > Memory Range: 0xfe900000-0xfe9fffff (rw,non-prefetchable) > Memory Range: 0xdf800000-0xdfffffff (rw,prefetchable) > Memory Range: 0xd0000000-0xd7ffffff (rw,prefetchable) > IRQ: 169 (no events) > Module Alias: "pci:v000015B3d00006278sv000015B3sd00006278bc0Csc06i00" > Driver Info #0: > Driver Status: ib_mthca is active > Driver Activation Cmd: "modprobe ib_mthca" > Config Status: cfg=new, avail=yes, need=no, active=unknown > Attached to: #17 (PCI bridge) > > blade9:~ # lspci -vv > [...] > 02:00.0 InfiniBand: Mellanox Technologies MT25208 InfiniHost III Ex HCA > (Tavor > compatibility mode) (rev a0) > Subsystem: Mellanox Technologies MT25208 InfiniHost III Ex HCA (Tavor > compatibility mode) > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Interrupt: pin A routed to IRQ 169 > Region 0: Memory at 00000000fe900000 (64-bit, non-prefetchable) > [size=1M] > Region 2: Memory at 00000000df800000 (64-bit, prefetchable) [size=8M] > Region 4: Memory at 00000000d0000000 (64-bit, prefetchable) > [size=128M] > Capabilities: [40] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [48] Vital Product Data > Capabilities: [90] Message Signalled Interrupts: 64bit+ Queue=0/5 > Enable- > Address: 0000000000000000 Data: 0000 > Capabilities: [84] MSI-X: Enable- Mask- TabSize=32 > Vector table: BAR=0 offset=00082000 > PBA: BAR=0 offset=00082200 > Capabilities: [60] Express Endpoint IRQ 0 > Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- > Device: Latency L0s <64ns, L1 unlimited > Device: AtnBtn- AtnInd- PwrInd- > Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- > Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > Device: MaxPayload 128 bytes, MaxReadReq 512 bytes > Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 8 > Link: Latency L0s unlimited, L1 unlimited > Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- > Link: Speed 2.5Gb/s, Width x8 > --->8---
Can you try with fw_cmd_doorbell? -- MST _______________________________________________ openib-general mailing list [email protected] http://openib.org/mailman/listinfo/openib-general To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general
