That's means everything is fine. Please try to use this.. *ldapmodify -W -x -D cn=admin,cn=config -b cn=config* -f /tmp/abc.ldif
If it will not work. Then i will tell you another trick to short out this. On Sat, Jan 25, 2014 at 1:14 AM, Warron S French <[email protected]>wrote: > Low Sensitivity/Aerospace Internal Use Only > > I attempted that command verbatim, substituting my own password, but the > UNIX Bash SHELL does its substitution and part of my password uses '!9' in > it. That was not working at all. > > However, instead of using "-w yourpassword" I substituted in " -W " > instead to get prompted at the command-line. That did work, and I got tons > of reasonable information back about the configuration. > > To be clear, I used the following on the command line since the UNIX shell > wanted to substitute... > > *ldapsearch -W -x -D cn=admin,cn=config -b cn=config* > > > I hope this gave you accurate feedback. > > > > *Warron French, MBA, SCSA* > > > > From: Vikas Parashar <[email protected]> > To: Warron S French <[email protected]>, > Cc: [email protected] > Date: 01/24/2014 02:33 PM > Subject: Re: OpenLDAP slapd problems - ldap_result: Can't contact > LDAP server (-1) --- Low Sensitivity/Aerospace Internal Use Only > ------------------------------ > > > > Hey, > > Please check, below is working or not?? > > > ldapsearch -w yourpassword -x -D cn=admin,cn=config -b cn=config > > > On Fri, Jan 24, 2014 at 11:37 PM, Warron S French < > *[email protected]* <[email protected]>> wrote: > Low Sensitivity/Aerospace Internal Use Only > > Hi Vikas, I have altered my command line to do the following now: > > * ldapmodify -x -D "cn=admin,cn=config" -W -d 256 -h * > *wsf-LabLDAP.lab.aero.org* <http://wsf-labldap.lab.aero.org/>* -p 389 -P > 3* > > I still get the exact same error, no change at all. > > > > > * Warron French, MBA, SCSA* > > > > From: Vikas Parashar <*[email protected]* <[email protected]> > > > To: Warron S French > <*[email protected]*<[email protected]>>, > > Cc: *[email protected]*<[email protected]> > Date: 01/24/2014 12:09 PM > Subject: Re: OpenLDAP slapd problems - ldap_result: Can't contact > LDAP server (-1) --- Low Sensitivity/Aerospace Internal Use Only > ------------------------------ > > > > > Hi, > > That error is clearly saying. "unable to connect" that's mean you need to > pass host as well.. > > > On Fri, Jan 24, 2014 at 9:58 PM, Warron S French < > *[email protected]* <[email protected]>> wrote: > Low Sensitivity/Aerospace Internal Use Only > > Working on a CentOS-6.5 server, running LTB Project's slapd-2.4.38. > > Someone suggested I implement a cn=admin,cn=config for a cn=config setup. > (I don't know how to technically word that). > > > Anyway, I need to make TLS-related changes and was told to do the > following command: > > * ldapmodify -x -D "cn=admin,cn=config" -W -d 256* > > ...then at the blank line type the following, each on a single line: > > Dn: cn=config > Changetype: modify > Add: olcTLSCipherSuite > OlcTLSCipherSuite: HIGH:MEDIUM+TLSv1+SSLv3 > <CTRL-D> > > > I have been getting an error reponse of: > * ldap_result: Can't contact LDAP server (-1)* > > This __ONLY__ occurs after I hit <CTRL-D>, not before. Yes, the daemon, > slapd, is actually running, but after this failure it abruptly stops. I > know this because in a separate terminal on the same system, I am running a > while-loop with a ps -e | grep slapd in it. > > > Please note the "-x" option according to the man page for ldapmodify is > supposed to Use simple authentication instead of SASL. > > > Thank you all for your help, hopefully you can: > > 1) tell me what this error means, and > 2) how to fix my problem so that I can complete the olcTLSxxxx changes I > need to implement. > > > > > > * Warron French, MBA, SCSA* > > Low Sensitivity/Aerospace Internal Use Only > > > > Low Sensitivity/Aerospace Internal Use Only > > > > Low Sensitivity/Aerospace Internal Use Only >
