-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Somebody in the thread at some point said: > Hi Andy, > > On Fri, Feb 01, 2008 at 11:44:12AM +0000, Andy Green wrote: > Somebody in the thread at some point said: > >>>>>> 2) If I scp a big file from another machine to /dev/null, the link >>>>>> stalls, >>>>>> and it looks like the module is dead. > Little bit more: > > [ 9758.890000] AR6000 scan complete: 0 >> Did you get this _after_ the link has stalled ?
Yes, stall happened at +8812s +/- 2s. Then the syslog had this behaviour: [ 8876.795000] AR6000 Neighbor Report Event [ 8876.795000] bssid 00:11:50:xx:xx:xx [ 8939.665000] AR6000 scan complete: 0 [ 8939.670000] AR6000 Neighbor Report Event [ 8939.670000] bssid 00:11:50:xx:xx:xx [ 9002.545000] AR6000 scan complete: 0 ... repeats stanza at 1m intervals ... [ 9633.145000] AR6000 Neighbor Report Event [ 9633.145000] bssid 00:11:50:xx:xx:xx [ 9696.015000] AR6000 scan complete: 0 [ 9696.020000] AR6000 Neighbor Report Event [ 9696.020000] bssid 00:11:50:xx:xx:xx [ 9745.990000] channel hint set to 2437 [ 9747.995000] Connect called with authmode 5 dot11 auth 1 PW crypto 4 PW crypto Len 0 GRP crypto 3 GRP crypto Len 0 [ 9758.890000] AR6000 scan complete: 0 [ 9758.900000] AR6000 Neighbor Report Event [ 9758.900000] bssid 00:11:50:xx:xx:xx [ 9761.900000] channel hint set to 2437 [ 9763.900000] Connect called with authmode 5 dot11 auth 1 PW crypto 4 PW crypto Len 0 GRP crypto 3 GRP crypto Len 0 [ 9781.910000] channel hint set to 2437 [ 9783.910000] Connect called with authmode 5 dot11 auth 1 PW crypto 4 PW crypto Len 0 GRP crypto 3 GRP crypto Len 0 [ 9801.920000] channel hint set to 2437 [ 9803.920000] Connect called with authmode 5 dot11 auth 1 PW crypto 4 PW crypto Len 0 GRP crypto 3 GRP crypto Len 0 [ 9821.770000] AR6000 scan complete: 0 [ 9821.775000] AR6000 Neighbor Report Event [ 9821.775000] bssid 00:11:50:xx:xx:xx [ 9821.935000] channel hint set to 2437 [ 9823.935000] Connect called with authmode 5 dot11 auth 1 PW crypto 4 PW crypto Len 0 GRP crypto 3 GRP crypto Len 0 [ 9823.940000] WMI Control Endpoint is FULL!!! > [ 9823.940000] WMI Control EP full, dropping packet : 0xC7C43EC0, len:54 > [ 9833.960000] WMI Control EP full, dropping packet : 0xC7E99A60, len:7 > [ 9833.960000] WMI Control EP full, dropping packet : 0xC5429E00, len:19 > [ 9841.965000] channel hint set to 2437 > [ 9843.965000] WMI Control EP full, dropping packet : 0xC7866900, len:2 > ... >> I never saw that. Usually, I stop getting SDIO interrupts from the target >> after the stall. That basically means we're dead. But if you got a scan >> complete event _after_ the stall, it means you _did_ receive an SDIO >> interrupt... Dunno why it should differ, this is the A5 shipped to me with whatever it had inside. Here's the dmesg for the init [ 3.760000] S3c2440 SDIO Host controller [ 3.865000] SDIO BusDriver - SDIO_GetBusOSDevice, registering driver: sdio_s3c24xx_hcd DMAmask: 0x0 [ 3.870000] pnp: the driver 'sdio_s3c24xx_hcd' has been registered [ 3.880000] mapped channel 0 to 0 [ 3.885000] S3c24xx SDIO: IRQ:37 Detect IRQ:0 DMA channel:0 [EMAIL PROTECTED] [EMAIL PROTECTED] kHz [ 3.895000] SDIO Bus Driver: HCD:sdio_s3c24xx should set module ptr! [ 3.905000] sdio_s3c24xx_hcd 00:00: driver attached [ 3.910000] sdio_s3c24xx_hcd 00:00: SDIO device, IDs SD_0008 (active) [ 3.920000] pnp: the driver 'sdio_wlan' has been registered [ 15.930000] CRCFAIL 0x1a3f [ 15.930000] CRCFAIL 0x1a3f [ 15.930000] Current Request Command:5, ARG:0x00000000 flags: 0x0008 [ 16.335000] CRCFAIL 0x1a3f [ 16.335000] CRCFAIL 0x1a3f [ 16.335000] Current Request Command:5, ARG:0x00100000 flags: 0x0008 [ 16.350000] CRCFAIL 0x1a3f [ 16.350000] CRCFAIL 0x1a3f [ 16.350000] Current Request Command:5, ARG:0x00100000 flags: 0x0008 [ 16.480000] sdio_wlan 00:01: driver attached [ 16.485000] sdio_wlan 00:01: SDIO device, IDs SD_0001 (active) [ 17.555000] Unsupported configuration opcode: 3 [ 17.560000] Unsupported configuration opcode: 5 [ 17.570000] ar6000_available [ 17.590000] BMI Get Target Info: Exit (ver: 0x20000028 type: 0x1) [ 17.600000] Block Size Set: 128 (target address:0x8000066C) [ 17.615000] ar6000_init() Got WMI @ 0xc7d96800. [ 17.655000] SDIO_INT_CTRL enable IRQ [ 17.665000] mac address = 00:12:cf:74:1f:b1 [ 17.675000] AR6000 Reg Code = 0x40000060 [ 17.680000] ar6000_init() WMI is ready [ 17.720000] ar6000_avail: name=eth0 htcTarget=0xc7f24000, dev=0xc7f30000 (0), ar=0xc7f304a0 >> Thanks for your time. No problem, let me know if you want any tests. - -Andy -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.7 (GNU/Linux) Comment: Using GnuPG with Fedora - http://enigmail.mozdev.org iD8DBQFHowqZOjLpvpq7dMoRAnDPAKCFyRtHrJJW5jp1qccTkW0VW+sYdgCeK9EG 3LGnpcplfXi8BBKpDLxdXyU= =vvv7 -----END PGP SIGNATURE-----
