-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
Lynn Nguyen wrote: > Sorry for such a late reply. but I tried using your way (also using ubuntu > 8.04), but this is what I get: > > Info: openocd.c:82 main(): Open On-Chip Debugger (2006-08-01 12:00 CEST) > Info: configuration.c:50 configuration_output_handler(): Command > ft2232_device_desc not found > Info: configuration.c:50 configuration_output_handler(): Command > ft2232_layout not found > Info: configuration.c:50 configuration_output_handler(): Command > ft2232_vid_pid not found > Error: jtag.c:1219 jtag_init(): No valid jtag interface found (ft2232) > > (using your openocd.cfg.). I'm using the openmoko debug board v3, with > gta01bv4. I'm connectin the dbug board to the laptop using the usb cord, and > connecting the debug board to the openmoko with the flex cable. Except also > I added the line ft2232_device_desc "Debug Board for Neo1973" like it says > on the wiki. http://wiki.openmoko.org/wiki/OpenOCD#openocd.cfg . > you also need another usb cable connect NEo1973 with debug board(or PC) for the power supply. and make sure you battery is powerful. see this: http://www.openmobilefree.net/images/26082008(002).jpg hope this help. > the lsusb output for the debug board: > Bus 001 Device 016: ID 1457:5118 > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 8 > idVendor 0x1457 > idProduct 0x5118 > bcdDevice 5.00 > iManufacturer 1 OpenMoko > iProduct 2 Debug Board for Neo1973 > iSerial 0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 55 > bNumInterfaces 2 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0x80 > (Bus Powered) > MaxPower 100mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 2 > bInterfaceClass 255 Vendor Specific Class > bInterfaceSubClass 255 Vendor Specific Subclass > bInterfaceProtocol 255 Vendor Specific Protocol > iInterface 2 Debug Board for Neo1973 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x02 EP 2 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 1 > bAlternateSetting 0 > bNumEndpoints 2 > bInterfaceClass 255 Vendor Specific Class > bInterfaceSubClass 255 Vendor Specific Subclass > bInterfaceProtocol 255 Vendor Specific Protocol > iInterface 2 Debug Board for Neo1973 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x83 EP 3 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x04 EP 4 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Device Status: 0x0000 > (Bus Powered) > > > On Wed, Aug 13, 2008 at 7:32 PM, xiangfu <[EMAIL PROTECTED]> wrote: > >> Lynn Nguyen wrote: >> >>> Hi, use I did use "sudo modprobe ftdi_sio vendor=0x1457 product=0x5118" >>> but >>> that doesn't work either. >>> >>> Tony-- what did you mean by puting the lib binary in the same folder? same >>> folder as what? and which one is the lib binary? >>> >>> xiangfu, do you think you could tell me the steps you use to make >>> everything >>> work? Like where you got the binaries and everything? Thanks! >>> >> i use UBUNTU 8.04 >> >> 1. sudo apt-get install openocd >> 2. sudo apt-get install libftdi0 >> 3. download the openocd.cfg (attachment) >> i put it in ~/ (home directory) so every time i run "sudo openocd" cd >> this directory or you will get >> Info: openocd.c:93 main(): Open On-Chip Debugger (2007-09-05 09:00 >> CEST) >> Error: configuration.c:121 parse_config_file(): couldn't open config >> file >> >> 4. if the openocd normal run then display something like: >> Info: openocd.c:93 main(): Open On-Chip Debugger (2007-09-05 09:00 >> CEST) >> Warning: telnet_server.c:545 telnet_init(): no telnet port specified, >> using default port 4444 >> >> 5. open another terminal " telnet localhost 4444" then we get a shell . >> >> >> >> >> telnet port 4444 >> gdb_port 3333 >> interface ft2232 >> jtag_speed 8 >> ft2232_vid_pid 0x1457 0x5118 >> ft2232_layout "jtagkey" >> reset_config trst_and_srst >> jtag_device 4 0x1 0xf 0xe >> daemon_startup attach >> target arm920t little reset_run 0 arm920t >> working_area 0 0x200000 0x4000 backup >> run_and_halt_time 0 5000 >> > -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.6 (GNU/Linux) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iQEVAwUBSLtLeRFuNemPXNFjAQIyyAf/QJWXSe44UzexQeog3Vjel/vj4WnfeIhK D/9PqJPVUUABRxgcjCKsOC+yiOVec64qCcHAgvobGz1Nug9lTbtVABKT8uTrl4fl hJgEG9jvgtVgO0r6sgoDSIm4o45pKkaBCVHTA+Y5atlU9NpbSn6lVd6g8GEYzpVI glcUefcAE3jcNN14AmwuMV4Of6O4jGxwUDgtqfDk8DjzrKbzCTVJDozdH5WOh1JZ 4DWQBBLoGkqZCHhjbfc9QgyR0fl+PqdcMSsrVtydKsRZsRdkXEK15YkJAnU7miII INTjPGjHrmbj82V0ZviOl9z9a2SfuzMRmMWPFWYiL6oReziHmU1otQ== =Lbeg -----END PGP SIGNATURE-----
