This is an automated email from Gerrit. "Antonio Borneo <[email protected]>" just uploaded a new patch set to Gerrit, which you can find at https://review.openocd.org/c/openocd/+/6656
-- gerrit commit 0363ddf87996d65fb41a19d9e734ff053c096664 Author: Antonio Borneo <[email protected]> Date: Fri Oct 8 11:53:56 2021 +0200 jtag/jlink: switch to command 'adapter serial' The driver jlink defines the command 'jlink serial' to specify the serial string of the adapter. Remove and deprecate the driver command, and use 'adapter serial'. Note: in former code the commands 'jlink serial' and 'jlink usb' were mutually exclusive; running one of them would invalidate the effect of a previous execution of the other. The new code gives priority to 'adapter serial', even if executed before 'jlink usb'. Change-Id: I920b0c136716f459b6fd6f7da8a01a7fa1ed389f Signed-off-by: Antonio Borneo <[email protected]> diff --git a/doc/openocd.texi b/doc/openocd.texi index 54e5b6ce1..7ae64dde9 100644 --- a/doc/openocd.texi +++ b/doc/openocd.texi @@ -2371,9 +2371,9 @@ This command is only available if your libusb1 is at least version 1.0.16. Specifies the @var{serial_string} of the adapter to use. If this command is not specified, serial strings are not considered. Only the following adapter drivers use the serial string from this command: -cmsis_dap, ft232r, ftdi, kitprog, presto, vsllink, xds110. +cmsis_dap, ft232r, ftdi, jlink, kitprog, presto, vsllink, xds110. The following adapters have their own command to specify the serial string: -hla, jlink, st-link. +hla, st-link. @end deffn @section Interface Drivers @@ -2855,12 +2855,6 @@ to the host. If not specified, USB addresses are not considered. Device selection via USB address is not always unambiguous. It is recommended to use the serial number instead, if possible. -As a configuration command, it can be used only before 'init'. -@end deffn -@deffn {Config Command} {jlink serial} <serial number> -Set the serial number of the interface, in case more than one adapter is -connected to the host. If not specified, serial numbers are not considered. - As a configuration command, it can be used only before 'init'. @end deffn @end deffn diff --git a/src/jtag/drivers/jlink.c b/src/jtag/drivers/jlink.c index ce1e9bfb7..15c2e3964 100644 --- a/src/jtag/drivers/jlink.c +++ b/src/jtag/drivers/jlink.c @@ -669,6 +669,21 @@ static int jlink_init(void) return ERROR_JTAG_INIT_FAILED; } + const char *serial = adapter_get_serial(); + if (serial) { + ret = jaylink_parse_serial_number(serial, &serial_number); + if (ret == JAYLINK_ERR) { + LOG_WARNING("Invalid serial number: %s. Ignore it", serial); + } else if (ret != JAYLINK_OK) { + LOG_WARNING("jaylink_parse_serial_number() failed: %s", jaylink_strerror(ret)); + jaylink_exit(jayctx); + return ERROR_JTAG_INIT_FAILED; + } else { + use_serial_number = true; + use_usb_address = false; + } + } + bool found_device; ret = jlink_open_device(JAYLINK_HIF_USB, &found_device); if (ret != ERROR_OK) @@ -979,38 +994,11 @@ COMMAND_HANDLER(jlink_usb_command) usb_address = tmp; - use_serial_number = false; use_usb_address = true; return ERROR_OK; } -COMMAND_HANDLER(jlink_serial_command) -{ - int ret; - - if (CMD_ARGC != 1) { - command_print(CMD, "Need exactly one argument for jlink serial"); - return ERROR_COMMAND_SYNTAX_ERROR; - } - - ret = jaylink_parse_serial_number(CMD_ARGV[0], &serial_number); - - if (ret == JAYLINK_ERR) { - command_print(CMD, "Invalid serial number: %s", CMD_ARGV[0]); - return ERROR_FAIL; - } else if (ret != JAYLINK_OK) { - command_print(CMD, "jaylink_parse_serial_number() failed: %s", - jaylink_strerror(ret)); - return ERROR_FAIL; - } - - use_serial_number = true; - use_usb_address = false; - - return ERROR_OK; -} - COMMAND_HANDLER(jlink_handle_hwstatus_command) { int ret; @@ -1932,13 +1920,6 @@ static const struct command_registration jlink_subcommand_handlers[] = { .help = "set the USB address of the device that should be used", .usage = "<0-3>" }, - { - .name = "serial", - .handler = &jlink_serial_command, - .mode = COMMAND_CONFIG, - .help = "set the serial number of the device that should be used", - .usage = "<serial number>" - }, { .name = "config", .handler = &jlink_handle_config_command, diff --git a/src/jtag/startup.tcl b/src/jtag/startup.tcl index d6c3b85b4..199ca04d6 100644 --- a/src/jtag/startup.tcl +++ b/src/jtag/startup.tcl @@ -759,6 +759,12 @@ proc "ftdi serial" {args} { eval adapter serial $args } +lappend _telnet_autocomplete_skip "jlink serial" +proc "jlink serial" {args} { + echo "DEPRECATED! use 'adapter serial' not 'jlink serial'" + eval adapter serial $args +} + lappend _telnet_autocomplete_skip kitprog_serial proc kitprog_serial args { echo "DEPRECATED! use 'adapter serial' not 'kitprog_serial'" diff --git a/tcl/interface/jlink.cfg b/tcl/interface/jlink.cfg index 51f420b7f..f9a18b05f 100644 --- a/tcl/interface/jlink.cfg +++ b/tcl/interface/jlink.cfg @@ -11,4 +11,4 @@ adapter driver jlink # # Example: Select J-Link with serial number 123456789 # -# jlink serial 123456789 +# adapter serial 123456789 --
