- **status**: new --> closed - **Resolution**: --> not an openocd bug - **Comment**:
Thanks! I'm closing it! --- ** [tickets:#367] Raspberry Pi 4 through SWD with STM32F4x (version: 0.12.0)** **Status:** closed **Milestone:** 0.11.0 **Labels:** raspberry pi 4 stm32f4x **Created:** Sat Oct 08, 2022 10:35 AM UTC by René **Last Updated:** Sat Oct 08, 2022 01:49 PM UTC **Owner:** nobody Hello, I got problems to get OpenOCD 0.12.0 running with a Raspberry Pi 4 and a STM32F401 microcontroller. I tested the SWD configuration with a Raspberry Pi 2 where I was succesfull. Now after also reading some threads, I adapted my configuration to the RPi4 but it still stops at this point: ~~~ Open On-Chip Debugger 0.12.0-rc1+dev-00023-gae937791d (2022-10-04-23:20) Licensed under GNU GPL v2 For bug reports, read http://openocd.org/doc/doxygen/bugs.html Info : BCM2835 GPIO JTAG/SWD bitbang driver Info : clock speed 2001 kHz Info : SWD DPIDR 0x00000000 Info : Listening on port 6666 for tcl connections Info : Listening on port 4444 for telnet connections ~~~ My Pin configuration is: Function | GPIO| ---------- | ---------- | nRST | 13 | SWDCLK | 24 | SWDIO | 25 | My raspberrypi2-native.cfg looks like this: ~~~ # SPDX-License-Identifier: GPL-2.0-or-later # # Config for using Raspberry Pi's expansion header # # This is best used with a fast enough buffer but also # is suitable for direct connection if the target voltage # matches RPi's 3.3V and the cable is short enough. # # Do not forget the GND connection, pin 6 of the expansion header. # adapter driver bcm2835gpio bcm2835gpio peripheral_base 0xFE000000 # Transition delay calculation: SPEED_COEFF/khz - SPEED_OFFSET # These depend on system clock, calibrated for stock 700MHz # bcm2835gpio speed SPEED_COEFF SPEED_OFFSET bcm2835gpio speed_coeffs 236181 60 # Each of the JTAG lines need a gpio number set: tck tms tdi tdo # Header pin numbers: 23 22 19 21 adapter gpio tck -chip 0 11 adapter gpio tms -chip 0 25 adapter gpio tdi -chip 0 10 adapter gpio tdo -chip 0 9 # Each of the SWD lines need a gpio number set: swclk swdio # Header pin numbers: 23 22 adapter gpio swclk -chip 0 24 adapter gpio swdio -chip 0 25 # If you define trst or srst, use appropriate reset_config # Header pin numbers: TRST - 26, SRST - 18 # adapter gpio trst -chip 0 7 # reset_config trst_only adapter gpio srst -chip 0 13 reset_config srst_only srst_push_pull # or if you have both connected, # reset_config trst_and_srst srst_push_pull ~~~ And my openocd.cfg like that: ~~~ source [find interface/raspberrypi2-native.cfg] transport select swd set CHIPNAME stm32f401 source [find target/stm32f4x.cfg] reset_config srst_nogate adapter srst delay 100 adapter srst pulse_width 100 init targets reset halt flash erase_sector 0 0 7 flash write_bank 0 test_fw.bin 0 reset shutdown ~~~ Did anyone manage to get OpenOCD 0.12.0 running on a RPi4? Thanks in advance! --- Sent from sourceforge.net because openocd-devel@lists.sourceforge.net is subscribed to https://sourceforge.net/p/openocd/tickets/ To unsubscribe from further messages, a project admin can change settings at https://sourceforge.net/p/openocd/admin/tickets/options. Or, if this is a mailing list, you can unsubscribe from the mailing list.