Good that it work now! I see that your dia.cfg is inspired from some STM32Lxx. It has inside some STM32 specific initialization that is probably causing issues with your chip. - Remove the lines related to the flash, - check that the SRAM is at the specified physical address 0x20000000 in the command for work-area, - remove the command mww specific for STM32 inside event examine-end, - if you have connected the reset wire, think about updating the command "reset_config none".
--- ** [tickets:#386] OpenOCD can't connect to Dialog DA1469x** **Status:** new **Milestone:** 0.11.0 **Labels:** swd da1469x jlink **Created:** Wed Mar 15, 2023 02:30 PM UTC by Maximilian Gerhardt **Last Updated:** Wed Mar 15, 2023 03:27 PM UTC **Owner:** nobody **Attachments:** - [dia.cfg](https://sourceforge.net/p/openocd/tickets/386/attachment/dia.cfg) (1.8 kB; application/octet-stream) - [jlink_logs.txt](https://sourceforge.net/p/openocd/tickets/386/attachment/jlink_logs.txt) (1.5 kB; text/plain) - [jlinkexe_good_connect.sr](https://sourceforge.net/p/openocd/tickets/386/attachment/jlinkexe_good_connect.sr) (3.6 kB; application/octet-stream) - [openocd_ap_info_good_connect.txt](https://sourceforge.net/p/openocd/tickets/386/attachment/openocd_ap_info_good_connect.txt) (1.8 kB; text/plain) - [openocd_bad_connect.sr](https://sourceforge.net/p/openocd/tickets/386/attachment/openocd_bad_connect.sr) (2.3 kB; application/octet-stream) Specifically, I have a custom DA14695 board, but it's the same with a [USB DevKit](https://www.renesas.com/br/en/products/wireless-connectivity/bluetooth-low-energy/da14695-00hqdevkt-u-smartbond-da14695-bluetooth-low-energy-52-usb-development-kit). Chip datasheet [see here](https://www.renesas.com/br/en/products/wireless-connectivity/bluetooth-low-energy/da14695-multi-core-bluetooth-52-soc-system-power-management-unit#document). It's a Cortex-M33 and Cortex-M0+ coprocessor (runs Bluetooth stack). Each have their own SWDIO+SWDCLK signals. I'm only interested in connecting to the Cortex-M33 main processor right now. Currently, the Dialog DA1469x is unsupported in OpenOCD. Only the proprietary JLinkExe can connect it. I want to be able to use OpenOCD and other debug adapters. So to get started with getting OpenOCD + JLink to work first without changing the debug adapter. this however fails horribly with the error Debug: 1132 515 jlink.c:2197 jlink_swd_run_queue(): SWD ack not OK: 7 JUNK Error: 1133 517 adi_v5_swd.c:144 swd_connect(): Error connecting DP: cannot read IDR While when using JLinkExe, it detects the chip just fine Found SW-DP with ID 0x0BE12477 AP0: AHB-AP (IDR: 0x14770015) Found Cortex-M33 r0p2, Little endian. OpenOCD fails at one of the very first steps, which is in the SWD protocol to do a LINERESET followed by the JTAG->SWD switch sequence, a LINERESET again and reading out the IDCODE. Looking at the SWD signals with a logic analyzers and PulseView, I compared the different signals that OpenOCD and JLinkExe produced and found that JLinkExe does a few more LINERESETs as the first attempt of reading IDCode actually fails, without a JTAG->SWD sequence in between. I'd also like to note that after using JLinkExe to connect, through some command sequence that I cannot reproduce anymore, openocd managed to connect using that config file. That's why I at least now -irlen 8 is right, it would not do that with -irlen 4. From there I coud do a "dap info". Here attached are the PulseView session files which should have the signal trace (with SWD decoding) in it, from JLinkExe and OpenOCD, next to the config file and JLinkExe output (sadly there are no verbose logs there). The OpenOCD command I'm using is 'openocd -f interface/jlink.cfg -c "transport select swd" -s . -f dia.cfg -c "gdb_memory_map disable"' I'd be happy for any pointer on how to get OpenOCD to talk to the Cortex-M33 successfully. --- Sent from sourceforge.net because openocd-devel@lists.sourceforge.net is subscribed to https://sourceforge.net/p/openocd/tickets/ To unsubscribe from further messages, a project admin can change settings at https://sourceforge.net/p/openocd/admin/tickets/options. Or, if this is a mailing list, you can unsubscribe from the mailing list.
