Hi,
committed the following patch
- cleanup target config scripts
Cheers
Spen
Index: target/target/lm3s3748.cfg
===================================================================
--- target/target/lm3s3748.cfg (revision 1201)
+++ target/target/lm3s3748.cfg (working copy)
@@ -20,7 +20,7 @@
set _CPUTAPID $CPUTAPID
} else {
# force an error till we get a good number
- set _CPUTAPID 0xffffffff
+ set _CPUTAPID 0x3ba00477
}
# RCLK
Index: target/target/lm3s6965.cfg
===================================================================
--- target/target/lm3s6965.cfg (revision 1201)
+++ target/target/lm3s6965.cfg (working copy)
@@ -18,7 +18,7 @@
set _CPUTAPID $CPUTAPID
} else {
# force an error till we get a good number
- set _CPUTAPID 0xffffffff
+ set _CPUTAPID 0x3ba00477
}
# jtag speed
@@ -33,7 +33,6 @@
#jtag scan chain
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 1 -irmask 0xf -expected-id
$_CPUTAPID
-
# the luminary variant causes a software reset rather than asserting SRST
# this stops the debug registers from being cleared
# this will be fixed in later revisions of silicon
Index: target/target/lm3s811.cfg
===================================================================
--- target/target/lm3s811.cfg (revision 1201)
+++ target/target/lm3s811.cfg (working copy)
@@ -17,7 +17,7 @@
set _CPUTAPID $CPUTAPID
} else {
# force an error till we get a good number
- set _CPUTAPID 0xffffffff
+ set _CPUTAPID 0x3ba00477
}
# jtag speed
Index: target/target/stm32.cfg
===================================================================
--- target/target/stm32.cfg (revision 1201)
+++ target/target/stm32.cfg (working copy)
@@ -12,7 +12,6 @@
set _ENDIAN little
}
-
# jtag speed
jtag_khz 500
@@ -51,7 +50,6 @@
$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000
-work-area-size 16384 -work-area-backup 0
-
flash bank stm32x 0 0 0 0 0
# For more information about the configuration files, take a look at:
Index: target/target/stm32stick.cfg
===================================================================
--- target/target/stm32stick.cfg (revision 1201)
+++ target/target/stm32stick.cfg (working copy)
@@ -35,7 +35,7 @@
# The boundery scan register, leave the "expected-id" undefined.
jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1e
-# What is this? It must be some extra chip on the stm32stick...
+# configure str750 connected to jtag chain
jtag newtap $_CHIPNAME unknown -irlen 4 -ircapture 0x1 -irmask 0x0f
set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
Index: target/target/str710.cfg
===================================================================
--- target/target/str710.cfg (revision 1201)
+++ target/target/str710.cfg (working copy)
@@ -16,10 +16,9 @@
if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
- set _CPUTAPID 0xffffffff
+ set _CPUTAPID 0x3f0f0f0f
}
-
#use combined on interfaces or targets that can't set TRST/SRST separately
reset_config trst_and_srst srst_pulls_trst
Index: target/target/str730.cfg
===================================================================
--- target/target/str730.cfg (revision 1201)
+++ target/target/str730.cfg (working copy)
@@ -17,10 +17,9 @@
if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
- set _CPUTAPID 0xffffffff
+ set _CPUTAPID 0x3f0f0f0f
}
-
#use combined on interfaces or targets that can't set TRST/SRST separately
#reset_config trst_and_srst srst_pulls_trst
reset_config trst_and_srst srst_pulls_trst
Index: target/target/str750.cfg
===================================================================
--- target/target/str750.cfg (revision 1201)
+++ target/target/str750.cfg (working copy)
@@ -15,13 +15,12 @@
if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
- set _CPUTAPID 0xffffffff
+ set _CPUTAPID 0x4f1f0041
}
# jtag speed
jtag_khz 10
-
#use combined on interfaces or targets that can't set TRST/SRST separately
#reset_config trst_and_srst srst_pulls_trst
reset_config trst_and_srst srst_pulls_trst
Index: target/target/str910-eval.cfg
===================================================================
--- target/target/str910-eval.cfg (revision 1201)
+++ target/target/str910-eval.cfg (working copy)
@@ -18,8 +18,7 @@
if { [info exists FLASHTAPID ] } {
set _FLASHTAPID $FLASHTAPID
} else {
- # Fixme with a correct number!
- set _FLASHTAPID 0xFFFFFFFF
+ set _FLASHTAPID 0x04570041
}
jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0xfe
-expected-id $_FLASHTAPID
@@ -34,7 +33,7 @@
if { [info exists BSTAPID ] } {
set _BSTAPID $BSTAPID
} else {
- set _BSTAPID 0xFFFFFFFF
+ set _BSTAPID 0x1457f041
}
jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1e
-expected-id $_BSTAPID
@@ -42,9 +41,21 @@
target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm966e
$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-virt
0x50000000 -work-area-size 16384 -work-area-backup 1
-flash bank str9xpec 0x00000000 0x00080000 0 0 0
+$_TARGETNAME configure -event reset-init {
+ # We can increase speed now that we know the target is halted.
+ #jtag_rclk 3000
+
+ # -- Enable 96K RAM
+ # PFQBC enabled / DTCM & AHB wait-states disabled
+ mww 0x5C002034 0x0191
-str9xpec enable_turbo 0
-str9xpec options_read 0
-str9xpec options_cmap 0 bank 1
-str9xpec options_write 0
+ str9x flash_config 0 4 2 0 0x80000
+ flash protect 0 0 7 off
+}
+
+#flash bank str9x <base> <size> 0 0 <target#> <variant>
+flash bank str9x 0x00000000 0x00080000 0 0 0
+flash bank str9x 0x00080000 0x00008000 0 0 0
+
+# For more information about the configuration files, take a look at:
+# openocd.texi
Index: target/target/str912.cfg
===================================================================
--- target/target/str912.cfg (revision 1201)
+++ target/target/str912.cfg (working copy)
@@ -12,8 +12,6 @@
set _ENDIAN little
}
-
-
# jtag speed. We need to stick to 16kHz until we've finished reset.
jtag_rclk 16
@@ -26,7 +24,7 @@
if { [info exists FLASHTAPID ] } {
set _FLASHTAPID $FLASHTAPID
} else {
- set _FLASHTAPID 0x25966041
+ set _FLASHTAPID 0x04570041
}
jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0xfe
-expected-id $_FLASHTAPID
Index: target/target/str9comstick.cfg
===================================================================
--- target/target/str9comstick.cfg (revision 1201)
+++ target/target/str9comstick.cfg (working copy)
@@ -14,7 +14,7 @@
if { [info exists FLASHTAPID ] } {
set _FLASHTAPID $FLASHTAPID
} else {
- set _FLASHTAPID 0xFFFFFFFF
+ set _FLASHTAPID 0x04570041
}
jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1
-expected-id $_FLASHTAPID
@@ -29,7 +29,7 @@
if { [info exists BSTAPID ] } {
set _BSTAPID $BSTAPID
} else {
- set _BSTAPID 0xFFFFFFFF
+ set _BSTAPID 0x1457f041
}
jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1
-expected-id $_BSTAPID
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
