For some reason, it appears the svn update isn't working. A fresh check
out of the repository and everything looks good. I'm probably doing
something wrong during the update. Is there a standard way to update my
working copy once you commit changes that I made? Thanks.
// Dean
Rick Altherr wrote:
> In my copy of the repo, at91sam9260.cfg is what at91sam9260minimal.cfg
> was. In fact, the checkin shows that at91sam9260.cfg was replaced.
> The fix in unknown-board-atmel-at91sam9260.cfg is still necessary.
>
> Committed in r1353.
>
> Rick
>
>
> On Jan 19, 2009, at 11:52 PM, Dean Glazeski wrote:
>
>> It looks like this patch didn't get applied quite right on r1350. It
>> appears that at91sam9260.cfg is the same as before, but
>> at91sam9260minimal.cfg is now gone. I went ahead and got the old
>> minimal config down and changed the at91sam9260.cfg file. There was
>> also a mistake I left in the 'unknown board' configuration file.
>> Patch is attached against r1350.
>>
>> // Dean
>>
>> Rick Altherr wrote:
>>> Committed in r1350.
>>>
>>> Rick
>>>
>>>
>>> On Jan 17, 2009, at 1:39 AM, Dean Glazeski wrote:
>>>
>>>> I went ahead and did some moving of some files relating to the
>>>> AT91SAM9260 and the Olimex SAM9-L9260 development board. I also
>>>> created another file for the Olimex JTAG TINY that doesn't include
>>>> the 'A'. Apparently, the description for the JTAG tiny can differ
>>>> between Windows and Linux Operating Systems and this can make a
>>>> difference, so I figured it might be nice to have two of them.
>>>> Probably could do an include to reduce redundancy, but I'll leave
>>>> that decision to some one else.
>>>>
>>>> Partial annoyance: the created patch file lists some files as
>>>> having a new property set called 'svn:mergeinfo', but their
>>>> contents are not included. Here is the 'svn status' on modified
>>>> rev1333
>>>>
>>>> R + src/target/target/at91sam9260.cfg
>>>> D src/target/target/at91sam9260minimal.cfg
>>>> A src/target/board/olimex_sam9_l9260.cfg
>>>> A + src/target/board/unknown-board-atmel-at91sam9260.cfg
>>>> A src/target/interface/olimex-jtag-tiny.cfg
>>>>
>>>> Here is the general idea because the two new files are not fully
>>>> listed in the patch:
>>>> target/at91sam9260.cfgR1333 ->
>>>> board/unknown-board-atmel-at91sam9260.cfg
>>>> target/at91sam9260minimal.cfgR1333 -> target/at91sam9260.cfg
>>>>
>>>> Actual patch file is attached. Some of the missing files are
>>>> attached as well.
>>>>
>>>> // Dean Glazeski
>>>>
>>>>
>>>> Property changes on: src/target/target/at91sam9260.cfg
>>>> ___________________________________________________________________
>>>> Added: svn:mergeinfo
>>>>
>>>> Index: src/target/target/at91sam9260minimal.cfg
>>>> ===================================================================
>>>> --- src/target/target/at91sam9260minimal.cfg (revision 1334)
>>>> +++ src/target/target/at91sam9260minimal.cfg (working copy)
>>>> @@ -1,42 +0,0 @@
>>>> -######################################
>>>> -# Target: Atmel AT91SAM9260
>>>> -######################################
>>>> -
>>>> -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME
>>>> -} else { - set _CHIPNAME at91sam9260
>>>> -}
>>>> -
>>>> -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN
>>>> -} else { - set _ENDIAN little
>>>> -}
>>>> -
>>>> -if { [info exists CPUTAPID ] } {
>>>> - set _CPUTAPID $CPUTAPID
>>>> -} else {
>>>> - # force an error till we get a good number
>>>> - set _CPUTAPID 0x0792603f
>>>> -}
>>>> -
>>>> -reset_config trst_and_srst
>>>> -
>>>> -#
>>>> -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf
>>>> -expected-id $_CPUTAPID
>>>> -
>>>> -jtag_nsrst_delay 200
>>>> -jtag_ntrst_delay 200
>>>> -
>>>> -######################
>>>> -# Target configuration
>>>> -######################
>>>> -
>>>> -set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
>>>> -target create $_TARGETNAME arm926ejs -endian $_ENDIAN
>>>> -chain-position $_TARGETNAME -variant arm926ejs
>>>> -
>>>> -# Internal sram1 memory
>>>> -$_TARGETNAME configure -work-area-virt 0 -work-area-phys
>>>> 0x00300000 -work-area-size 0x1000 -work-area-backup 1
>>>> -
>>>> -
>>>> Index: src/target/board/olimex_sam9_l9260.cfg
>>>> ===================================================================
>>>> --- src/target/board/olimex_sam9_l9260.cfg (revision 0)
>>>> +++ src/target/board/olimex_sam9_l9260.cfg (revision 0)
>>>> @@ -0,0 +1,10 @@
>>>> +##
>>>> +# Olimex SAM9-L9260 board configuration file
>>>> +#
>>>> +# Date Author Change
>>>> +# ---- ------ ------
>>>> +# 17/Jan/2009 Dean Glazeski Initial Creation
>>>> +#
>>>> +##
>>>> +
>>>> +source [find target/at91sam9260.cfg]
>>>>
>>>> Property changes on:
>>>> src/target/board/unknown-board-atmel-at91sam9260.cfg
>>>> ___________________________________________________________________
>>>> Added: svn:mergeinfo
>>>>
>>>> Index: src/target/interface/olimex-jtag-tiny.cfg
>>>> ===================================================================
>>>> --- src/target/interface/olimex-jtag-tiny.cfg (revision 0)
>>>> +++ src/target/interface/olimex-jtag-tiny.cfg (revision 0)
>>>> @@ -0,0 +1,9 @@
>>>> +##
>>>> +# Olimex JTAG TINY USB Debugger
>>>> +# Linux USB tends to see the device description without the 'A' as
>>>> in target/olimex-jtag-tiny.cfg,
>>>> +# but Windows still needs the 'A'. This is a replacement for
>>>> Linux users.
>>>> +##
>>>> +interface ft2232
>>>> +ft2232_device_desc "Olimex OpenOCD JTAG TINY"
>>>> +ft2232_layout olimex-jtag
>>>> +ft2232_vid_pid 0x15ba 0x0004
>>>> # Thanks to Pieter Conradie for this script!
>>>> # Target: Atmel AT91SAM9260
>>>> ######################################
>>>>
>>>> # We add to the minimal configuration.
>>>> source [find target/at91sam9260minimal.cfg]
>>>>
>>>> ######################
>>>> # Target configuration
>>>> ######################
>>>>
>>>> $_TARGETNAME configure -event reset-init {
>>>> # at reset chip runs at 32khz
>>>> jtag_khz 8
>>>> mww 0xfffffd08 0xa5000501 # RSTC_MR : enable user reset
>>>> mww 0xfffffd44 0x00008000 # WDT_MR : disable watchdog
>>>>
>>>> mww 0xfffffc20 0x00004001 # CKGR_MOR : enable the main
>>>> oscillator
>>>> sleep 20 # wait 20 ms
>>>> mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main
>>>> oscillator
>>>> sleep 10 # wait 10 ms
>>>> mww 0xfffffc28 0x2060bf09 # CKGR_PLLAR: Set PLLA
>>>> Register for 198,656MHz
>>>> sleep 20 # wait 20 ms
>>>> mww 0xfffffc30 0x00000101 # PMC_MCKR : Select prescaler
>>>> sleep 10 # wait 10 ms
>>>> mww 0xfffffc30 0x00000102 # PMC_MCKR : Clock from PLLA
>>>> is selected
>>>> sleep 10 # wait 10 ms
>>>>
>>>> # Now run at anything fast... ie: 10mhz!
>>>> jtag_khz 10000 # Increase JTAG Speed to 6 MHz
>>>> arm7_9 dcc_downloads enable # Enable faster DCC downloads
>>>>
>>>> mww 0xffffec00 0x01020102 # SMC_SETUP0 : Setup SMC for
>>>> Intel NOR Flash JS28F128P30T85 128MBit
>>>> mww 0xffffec04 0x09070806 # SMC_PULSE0
>>>> mww 0xffffec08 0x000d000b # SMC_CYCLE0
>>>> mww 0xffffec0c 0x00001003 # SMC_MODE0
>>>>
>>>> flash probe 0 # Identify flash bank 0
>>>>
>>>> mww 0xfffff870 0xffff0000 # PIO_ASR : Select peripheral
>>>> function for D15..D31
>>>> mww 0xfffff804 0xffff0000 # PIO_PDR : Disable PIO
>>>> function for D15..D31
>>>>
>>>> mww 0xffffef1c 0x2 # EBI_CSA : Assign EBI Chip
>>>> Select 1 to SDRAM
>>>>
>>>> #mww 0xffffea08 0x85227259 # SDRAMC_CR : Configure SDRAM
>>>> (2 x Samsung K4S561632H-UC75 : 4M x 16Bit x 4 Banks)
>>>> mww 0xffffea08 0x85227254 # SDRAMC_CR : Configure SDRAM
>>>> (2 x Samsung K4S641632H-UC75 : 1M x 16Bit x 4 Banks)
>>>>
>>>> mww 0xffffea00 0x1 # SDRAMC_MR : issue a NOP command
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x2 # SDRAMC_MR : issue an 'All
>>>> Banks Precharge' command
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x4 # SDRAMC_MR : issue 8 x
>>>> 'Auto-Refresh' Command
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x4
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x4
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x4
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x4
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x4
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x4
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x4
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x3 # SDRAMC_MR : issue a 'Load
>>>> Mode Register' command
>>>> mww 0x20000000 0
>>>> mww 0xffffea00 0x0 # SDRAMC_MR : normal mode
>>>> mww 0x20000000 0
>>>> mww 0xffffea04 0x5d2 # SDRAMC_TR : Set refresh
>>>> timer count to 15us
>>>> }
>>>>
>>>>
>>>> #####################
>>>> # Flash configuration
>>>> #####################
>>>>
>>>> #flash bank cfi <base> <size> <chip width> <bus width> <target#>
>>>> flash bank cfi 0x10000000 0x01000000 2 2 0
>>>>
>>>> ######################################
>>>> # Target: Atmel AT91SAM9260
>>>> ######################################
>>>>
>>>> if { [info exists CHIPNAME] } { set _CHIPNAME $CHIPNAME
>>>> } else { set _CHIPNAME at91sam9260
>>>> }
>>>>
>>>> if { [info exists ENDIAN] } { set _ENDIAN $ENDIAN
>>>> } else { set _ENDIAN little
>>>> }
>>>>
>>>> if { [info exists CPUTAPID ] } {
>>>> set _CPUTAPID $CPUTAPID
>>>> } else {
>>>> # force an error till we get a good number
>>>> set _CPUTAPID 0x0792603f
>>>> }
>>>>
>>>> reset_config trst_and_srst
>>>>
>>>> #
>>>> jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf
>>>> -expected-id $_CPUTAPID
>>>>
>>>> jtag_nsrst_delay 200
>>>> jtag_ntrst_delay 200
>>>>
>>>> ######################
>>>> # Target configuration
>>>> ######################
>>>>
>>>> set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
>>>> target create $_TARGETNAME arm926ejs -endian $_ENDIAN
>>>> -chain-position $_TARGETNAME -variant arm926ejs
>>>>
>>>> # Internal sram1 memory
>>>> $_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000
>>>> -work-area-size 0x1000 -work-area-backup 1
>>>>
>>>>
>>>> _______________________________________________
>>>> Openocd-development mailing list
>>>> [email protected]
>>>> https://lists.berlios.de/mailman/listinfo/openocd-development
>>>
>>> --
>>> Rick Altherr
>>> [email protected]
>>>
>>> "He said he hadn't had a byte in three days. I had a short, so I
>>> split it with him."
>>> -- Unsigned
>>>
>>>
>>>
>>
>> Index: src/target/target/at91sam9260.cfg
>> ===================================================================
>> --- src/target/target/at91sam9260.cfg (revision 1350)
>> +++ src/target/target/at91sam9260.cfg (working copy)
>> @@ -1,82 +1,42 @@
>> -# Thanks to Pieter Conradie for this script!
>> +######################################
>> # Target: Atmel AT91SAM9260
>> ######################################
>>
>> -# We add to the minimal configuration.
>> -source [find target/at91sam9260minimal.cfg]
>> +if { [info exists CHIPNAME] } {
>> + set _CHIPNAME $CHIPNAME
>> +} else {
>> + set _CHIPNAME at91sam9260
>> +}
>>
>> -######################
>> -# Target configuration
>> -######################
>> +if { [info exists ENDIAN] } {
>> + set _ENDIAN $ENDIAN
>> +} else {
>> + set _ENDIAN little
>> +}
>>
>> -$_TARGETNAME configure -event reset-init {
>> - # at reset chip runs at 32khz
>> - jtag_khz 8
>> - mww 0xfffffd08 0xa5000501 # RSTC_MR : enable user reset
>> - mww 0xfffffd44 0x00008000 # WDT_MR : disable watchdog
>> +if { [info exists CPUTAPID ] } {
>> + set _CPUTAPID $CPUTAPID
>> +} else {
>> + # force an error till we get a good number
>> + set _CPUTAPID 0x0792603f
>> +}
>>
>> - mww 0xfffffc20 0x00004001 # CKGR_MOR : enable the main
>> oscillator
>> - sleep 20 # wait 20 ms
>> - mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main
>> oscillator
>> - sleep 10 # wait 10 ms
>> - mww 0xfffffc28 0x2060bf09 # CKGR_PLLAR: Set PLLA
>> Register for 198,656MHz
>> - sleep 20 # wait 20 ms
>> - mww 0xfffffc30 0x00000101 # PMC_MCKR : Select prescaler
>> - sleep 10 # wait 10 ms
>> - mww 0xfffffc30 0x00000102 # PMC_MCKR : Clock from PLLA
>> is selected
>> - sleep 10 # wait 10 ms
>> +reset_config trst_and_srst
>>
>> - # Now run at anything fast... ie: 10mhz!
>> - jtag_khz 10000 # Increase JTAG Speed to 6 MHz
>> - arm7_9 dcc_downloads enable # Enable faster DCC downloads
>> +#
>> +jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf
>> -expected-id $_CPUTAPID
>>
>> - mww 0xffffec00 0x01020102 # SMC_SETUP0 : Setup SMC for
>> Intel NOR Flash JS28F128P30T85 128MBit
>> - mww 0xffffec04 0x09070806 # SMC_PULSE0
>> - mww 0xffffec08 0x000d000b # SMC_CYCLE0
>> - mww 0xffffec0c 0x00001003 # SMC_MODE0
>> +jtag_nsrst_delay 200
>> +jtag_ntrst_delay 200
>>
>> - flash probe 0 # Identify flash bank 0
>> +######################
>> +# Target configuration
>> +######################
>>
>> - mww 0xfffff870 0xffff0000 # PIO_ASR : Select peripheral
>> function for D15..D31
>> - mww 0xfffff804 0xffff0000 # PIO_PDR : Disable PIO
>> function for D15..D31
>> +set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
>> +target create $_TARGETNAME arm926ejs -endian $_ENDIAN
>> -chain-position $_TARGETNAME -variant arm926ejs
>>
>> - mww 0xffffef1c 0x2 # EBI_CSA : Assign EBI Chip
>> Select 1 to SDRAM
>> +# Internal sram1 memory
>> +$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000
>> -work-area-size 0x1000 -work-area-backup 1
>>
>> - #mww 0xffffea08 0x85227259 # SDRAMC_CR : Configure SDRAM
>> (2 x Samsung K4S561632H-UC75 : 4M x 16Bit x 4 Banks)
>> - mww 0xffffea08 0x85227254 # SDRAMC_CR : Configure SDRAM
>> (2 x Samsung K4S641632H-UC75 : 1M x 16Bit x 4 Banks)
>>
>> - mww 0xffffea00 0x1 # SDRAMC_MR : issue a NOP command
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x2 # SDRAMC_MR : issue an 'All
>> Banks Precharge' command
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x4 # SDRAMC_MR : issue 8 x
>> 'Auto-Refresh' Command
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x4
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x4
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x4
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x4
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x4
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x4
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x4
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x3 # SDRAMC_MR : issue a 'Load
>> Mode Register' command
>> - mww 0x20000000 0
>> - mww 0xffffea00 0x0 # SDRAMC_MR : normal mode
>> - mww 0x20000000 0
>> - mww 0xffffea04 0x5d2 # SDRAMC_TR : Set refresh
>> timer count to 15us
>> -}
>> -
>> -
>> -#####################
>> -# Flash configuration
>> -#####################
>> -
>> -#flash bank cfi <base> <size> <chip width> <bus width> <target#>
>> -flash bank cfi 0x10000000 0x01000000 2 2 0
>> -
>> Index: src/target/board/unknown-board-atmel-at91sam9260.cfg
>> ===================================================================
>> --- src/target/board/unknown-board-atmel-at91sam9260.cfg (revision
>> 1350)
>> +++ src/target/board/unknown-board-atmel-at91sam9260.cfg (working
>> copy)
>> @@ -3,7 +3,7 @@
>> ######################################
>>
>> # We add to the minimal configuration.
>> -source [find target/at91sam9260minimal.cfg]
>> +source [find target/at91sam9260.cfg]
>>
>> ######################
>> # Target configuration
>
> --
> Rick Altherr
> [email protected]
>
> "He said he hadn't had a byte in three days. I had a short, so I split
> it with him."
> -- Unsigned
>
>
>
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
