Magnus Lundin wrote:
> Hi
>
> I think yuo can use something like:
>
> targets omap3.cpu
Doesn't work:
-- cut --
> targets omap3.cpu
Target: omap3.cpu unknown, try one of:
CmdName Type Endian AbsChainPos Name State
-- ---------- ---------- ---------- ----------- ------------- ----------
>
-- cut --
Anybody else with an idea how to configure commands like e.g.
'cortex_m3 dap 0' to work on one of the several TAPs in a muli-TAP
device? I.e. how to specify the TAP they should deal with?
> cortex_m3 dap 0
Any idea about
-- cut --
> cortex_m3 dap 0
invalid command name "cortex_m3_dap"
called at file "command.c", line 456
called at file "embedded:startup.tcl", line 89
called at file "embedded:startup.tcl", line 93
-- cut --
?
In a first step this doesn't look multi-TAP related? Some wrong
configuration?
Best regards
Dirk
> I have never used any target with multiple taps so this is just guessing
> from my side.
>
> Regards,
> Magnus
>
>
> Dirk Behme wrote:
>> Magnus Lundin wrote:
>>> Hi
>>>
>>> The following patch is a first step towards support for sevaral AP in
>>> one dap.
>>>
>>> - Adds a apsel variable, corresponding to the corresponding field in
>>> the DP SELECT register, to the swjdap structure.
>>> - adds a function swjdp_apselect(swjdp_common_t *swjdp,u8 apsel) to
>>> set this variable.
>>> - adds two cortex_m3 interactive commands
>>> cortex_m3 dap #n Shows the contents of ROM/Debug base
>>> register and AP ID Register
>>> cortex_m3 apsel #n Configures to use AP #n in subsequent memory
>>> accesses.
>>>
>>> This should be a possible starting point to explore other debug
>>> configurations that the Cortex_M3
>>>
>>> Tested on STM32 with no problems found. I dont have any A8 hardware.
>> I tried to use the commands above with OMAP3 Cortex A8. Two questions:
>>
>> - OMAP3 has (at least) two TAPs
>>
>>> scan_chain
>> TapName | Enabled | IdCode Expected IrLen
>> IrCap IrMask Instr
>> ---|--------------------|---------|------------|------------|------|------|------|---------
>>
>>
>> 0 | omap3.cpu | Y | 0x00000000 | 0x0b6d602f | 0x04 |
>> 0x01 | 0x00 | 0x0f
>> 1 | omap3.jrc | Y | 0x0b7ae02f | 0x0b7ae02f | 0x06 |
>> 0x01 | 0x0f | 0x3f
>>
>> while 'omap3.cpu' is "Cortex A8" where I think above cortex_m3
>> commands should work with. How do I tell these commands which TAP to
>> deal with? I.e. how to select which TAP the DAP and AP commands to
>> work with?
>>
>> - OpenOCD revision 1462 with the patch from this mail:
>>
>> -- cut --
>>> cortex_m3 dap 0
>> invalid command name "cortex_m3_dap"
>> called at file "command.c", line 456
>> called at file "embedded:startup.tcl", line 89
>> called at file "embedded:startup.tcl", line 93
>>> cortex_m3 dap 1
>> invalid command name "cortex_m3_dap"
>> called at file "command.c", line 456
>> called at file "embedded:startup.tcl", line 89
>> called at file "embedded:startup.tcl", line 93
>>> cortex_m3 apsel 0
>> invalid command name "cortex_m3_apsel"
>> called at file "command.c", line 456
>> called at file "embedded:startup.tcl", line 89
>> called at file "embedded:startup.tcl", line 93
>>> cortex_m3 apsel 1
>> invalid command name "cortex_m3_apsel"
>> called at file "command.c", line 456
>> called at file "embedded:startup.tcl", line 89
>> called at file "embedded:startup.tcl", line 93
>> -- cut --
>>
>> Any hint?
>>
>> Many thanks and best regards
>>
>> Dirk
>
> _______________________________________________
> Openocd-development mailing list
> [email protected]
> https://lists.berlios.de/mailman/listinfo/openocd-development
>
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
