Move the short chapter about JIM-Tcl earlier, so that we
can reasonably assume it's been introduced before we start
presenting things that presume such an introduction.
Plus a few minor typo-level fixes.
---
doc/openocd.texi | 88 ++++++++++++++++++++++++++++-------------------------
1 file changed, 48 insertions(+), 40 deletions(-)
Move the short chapter about JIM-Tcl earlier, so that we
can reasonably assume it's been introduced before we start
presenting things that presume such an introduction.
Plus a few minor typo-level fixes.
---
doc/openocd.texi | 88 ++++++++++++++++++++++++++++-------------------------
1 file changed, 48 insertions(+), 40 deletions(-)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -63,10 +63,10 @@ Free Documentation License''.
* Developers:: OpenOCD Developers
* Building OpenOCD:: Building OpenOCD From SVN
* JTAG Hardware Dongles:: JTAG Hardware Dongles
+* About JIM-Tcl:: About JIM-Tcl
* Running:: Running OpenOCD
* OpenOCD Project Setup:: OpenOCD Project Setup
* Config File Guidelines:: Config File Guidelines
-* About JIM-Tcl:: About JIM-Tcl
* Daemon Configuration:: Daemon Configuration
* Interface - Dongle Configuration:: Interface - Dongle Configuration
* Reset Configuration:: Reset Configuration
@@ -659,6 +659,50 @@ FlashLINK JTAG programing cable for PSD
@end itemize
+...@node About JIM-Tcl
+...@chapter About JIM-Tcl
+...@cindex JIM Tcl
+...@cindex tcl
+
+OpenOCD includes a small ``Tcl Interpreter'' known as JIM-Tcl.
+This programming language provides a simple and extensible
+command interpreter.
+
+All commands presented in this Guide are extensions to JIM-Tcl.
+You can use them as simple commands, without needing to learn
+much of anything about Tcl.
+Alternatively, can write Tcl programs with them.
+
+You can learn more about JIM at its website, @url{http://jim.berlios.de}.
+
+...@itemize @bullet
+...@item @b{JIM vs. Tcl}
+...@* JIM-TCL is a stripped down version of the well known Tcl language,
+which can be found here: @url{http://www.tcl.tk}. JIM-Tcl has far
+fewer features. JIM-Tcl is a single .C file and a single .H file and
+implements the basic Tcl command set. In contrast: Tcl 8.6 is a
+4.2 MB .zip file containing 1540 files.
+
+...@item @b{Missing Features}
+...@* Our practice has been: Add/clone the real Tcl feature if/when
+needed. We welcome JIM Tcl improvements, not bloat.
+
+...@item @b{Scripts}
+...@* OpenOCD configuration scripts are JIM Tcl Scripts. OpenOCD's
+command interpreter today is a mixture of (newer)
+JIM-Tcl commands, and (older) the orginal command interpreter.
+
+...@item @b{Commands}
+...@* At the OpenOCD telnet command line (or via the GDB mon command) one
+can type a Tcl for() loop, set variables, etc.
+
+...@item @b{Historical Note}
+...@* JIM-Tcl was introduced to OpenOCD in spring 2008.
+
+...@item @b{Need a crash course in Tcl?}
+...@*@xref{Tcl Crash Course}.
+...@end itemize
+
@node Running
@chapter Running
@cindex command line options
@@ -693,7 +737,7 @@ clients (Telnet, GDB, Other).
If you are having problems, you can enable internal debug messages via
the ``-d'' option.
-Also it is possible to interleave commands w/config scripts using the
+Also it is possible to interleave JIM-Tcl commands w/config scripts using the
@option{-c} command line switch.
To enable debug output (when reporting problems or working on OpenOCD
@@ -808,7 +852,7 @@ single directory for your work with a gi
When you start OpenOCD from that directory,
it searches there first for configuration files
and for code you upload to the target board.
-It is also be the natural place to write files,
+It is also the natural place to write files,
such as log files and data you download from the board.
@section Configuration Basics
@@ -848,7 +892,7 @@ openocd -f interface/signalyzer.cfg \
You could wrap such long command lines in shell scripts,
each supporting a different development task.
-One might re-flash the board with specific firmware version.
+One might re-flash the board with a specific firmware version.
Another might set up a particular debugging or run-time environment.
Here we will focus on the simpler solution: one user config
@@ -1456,42 +1500,6 @@ Examples:
@item pxa270 - again - CS0 flash - it goes in the board file.
@end itemize
-...@node About JIM-Tcl
-...@chapter About JIM-Tcl
-...@cindex JIM Tcl
-...@cindex tcl
-
-OpenOCD includes a small ``TCL Interpreter'' known as JIM-TCL. You can
-learn more about JIM here: @url{http://jim.berlios.de}
-
-...@itemize @bullet
-...@item @b{JIM vs. Tcl}
-...@* JIM-TCL is a stripped down version of the well known Tcl language,
-which can be found here: @url{http://www.tcl.tk}. JIM-Tcl has far
-fewer features. JIM-Tcl is a single .C file and a single .H file and
-impliments the basic Tcl command set along. In contrast: Tcl 8.6 is a
-4.2 MB .zip file containing 1540 files.
-
-...@item @b{Missing Features}
-...@* Our practice has been: Add/clone the real Tcl feature if/when
-needed. We welcome JIM Tcl improvements, not bloat.
-
-...@item @b{Scripts}
-...@* OpenOCD configuration scripts are JIM Tcl Scripts. OpenOCD's
-command interpreter today is a mixture of (newer)
-JIM-Tcl commands, and (older) the orginal command interpreter.
-
-...@item @b{Commands}
-...@* At the OpenOCD telnet command line (or via the GDB mon command) one
-can type a Tcl for() loop, set variables, etc.
-
-...@item @b{Historical Note}
-...@* JIM-Tcl was introduced to OpenOCD in spring 2008.
-
-...@item @b{Need a crash course in Tcl?}
-...@*@xref{Tcl Crash Course}.
-...@end itemize
-
@node Daemon Configuration
@chapter Daemon Configuration
@cindex initialization
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
