The following patch will add chip support for LM3S1968 and
board config file for EK-LM3S1968. Tested against SVN2578.
Index: tcl/target/lm3s1968.cfg
===================================================================
--- tcl/target/lm3s1968.cfg (revision 0)
+++ tcl/target/lm3s1968.cfg (revision 0)
@@ -0,0 +1,36 @@
+# Script for luminary lm3s1968
+
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME lm3s1968
+}
+
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ # this defaults to a little endian
+ set _ENDIAN little
+}
+
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ # force an error till we get a good number
+ set _CPUTAPID 0x3ba00477
+}
+
+#jtag scan chain
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 1 -irmask 0xf
-expected-id $_CPUTAPID
+
+# the luminary variant causes a software reset rather than asserting SRST
+# this stops the debug registers from being cleared
+# this will be fixed in later revisions of silicon
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position
$_TARGETNAME -variant lm3s
+
+# 4k working area at base of ram
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000
-work-area-size 0x4000 -work-area-backup 0
+
+#flash configuration
+flash bank stellaris 0 0 0 0 0
Index: tcl/board/ek-lm3s1968.cfg
===================================================================
--- tcl/board/ek-lm3s1968.cfg (revision 0)
+++ tcl/board/ek-lm3s1968.cfg (revision 0)
@@ -0,0 +1,23 @@
+#
+# Luminary Micro Stellaris LM3S1968 Evaluation Kits
+#
+# http://www.luminarymicro.com/products/lm3s1968_evaluation_kits.html
+
+# NOTE: to use J-Link instead of the on-board interface,
+# you may also need to reduce jtag_khz to be about 1200.
+# source [find interface/jlink.cfg]
+
+# include the FT2232 interface config for on-board JTAG interface
+source [find interface/luminary.cfg]
+
+# include the target config
+source [find target/lm3s1968.cfg]
+
+# jtag speed
+jtag_khz 3000
+
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
+#LM3S1968 Evaluation Board has only srst
+reset_config srst_only
--
Xiaofan http://mcuee.blogspot.com
Index: tcl/target/lm3s1968.cfg
===================================================================
--- tcl/target/lm3s1968.cfg (revision 0)
+++ tcl/target/lm3s1968.cfg (revision 0)
@@ -0,0 +1,36 @@
+# Script for luminary lm3s1968
+
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME lm3s1968
+}
+
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ # this defaults to a little endian
+ set _ENDIAN little
+}
+
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ # force an error till we get a good number
+ set _CPUTAPID 0x3ba00477
+}
+
+#jtag scan chain
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 1 -irmask 0xf -expected-id
$_CPUTAPID
+
+# the luminary variant causes a software reset rather than asserting SRST
+# this stops the debug registers from being cleared
+# this will be fixed in later revisions of silicon
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position
$_TARGETNAME -variant lm3s
+
+# 4k working area at base of ram
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000
-work-area-size 0x4000 -work-area-backup 0
+
+#flash configuration
+flash bank stellaris 0 0 0 0 0
Index: tcl/board/ek-lm3s1968.cfg
===================================================================
--- tcl/board/ek-lm3s1968.cfg (revision 0)
+++ tcl/board/ek-lm3s1968.cfg (revision 0)
@@ -0,0 +1,23 @@
+#
+# Luminary Micro Stellaris LM3S1968 Evaluation Kits
+#
+# http://www.luminarymicro.com/products/lm3s1968_evaluation_kits.html
+
+# NOTE: to use J-Link instead of the on-board interface,
+# you may also need to reduce jtag_khz to be about 1200.
+# source [find interface/jlink.cfg]
+
+# include the FT2232 interface config for on-board JTAG interface
+source [find interface/luminary.cfg]
+
+# include the target config
+source [find target/lm3s1968.cfg]
+
+# jtag speed
+jtag_khz 3000
+
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
+#LM3S1968 Evaluation Board has only srst
+reset_config srst_only
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
